Xpe reboot when i browse the Cf or plug an usb key ??

  • Thread starter Thread starter Korben
  • Start date Start date
K

Korben

Hi all,

Embedded system is running with a Icop panel pc cpu vortex pdx-057T. The
image was builded with Xpe FP2007 with Xpe Rollup1,Rollup1Api on 4giga ntfs
Lexar Cf
Here the end of the fba log.
I suspected the bloody ewf configuration.
In the setting of the ewf filter, the check box "start ewf enable" was
clear.
ewfmgr c: is not functioning.

Tks vm to contribute


14:04:15 PM - ConfigureEwf() Start.
14:04:15 PM - Getting EWF config parameters from registry.
14:04:15 PM - Non El Torito disk configuration.
14:04:15 PM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1.
14:04:15 PM - Protected Volume Config #0 :
14:04:15 PM - Disk= 0,Part= 1,Type= RAM.
14:04:15 PM - Enable= Disabled, Optimize= 0, LazyWrite= N.
14:04:15 PM - Found 1 Hard Disks.
14:04:15 PM - Disk #0 layout info:
14:04:15 PM - PRIMARY partition,start=0x0000000000007e00,
len=0x00000000eec1d000, type= 7
14:04:15 PM - Can't create EWF partition size = 0x000000000000fc00 on
disk# 0.
14:04:15 PM - Failed to create EWF partition.
14:04:15 PM - ConfigureEwf() End, status = 0x80070057.
14:04:15 PM - [CallEntryPointThread] C:\WINDOWS\system32\ewfdll.dll,
ConfigureEwf
14:04:15 PM - [FBASetProgressText] Resetting Setup Flag...
14:05:08 PM - [FBADoProperShutdown] Sleeping...
14:05:18 PM - [FBADoProperShutdown] Rebooting system...
 
From the log it appears that EWF was not able to create the EWF partition.
This can be due to one of the following reasons

(1) Your CF card does not support creating additional partitions. In this
case use RAM-REG mode instead of RAM mode. RAM-REG does not need an
additional partition to store configuration information.
(2) Your CF supports additional partitions but you did not leave enough
unpartitioned space on your disk. This is necessary to allow EWF setup to
create its custom partition. For RAM mode , few mega bytes of unpartitioned
space is sufficient.

Thanks
Srikanth
 
Hi Srikanth,

You right, i left 1 giga on my unpartitioned free space Cf and then ewf
works.
But i'm still fighting with my reboot system.
Thk vm.


"Srikanth Kamath [MSFT]" <[email protected]> a
écrit dans le message de (e-mail address removed)...
From the log it appears that EWF was not able to create the EWF partition.
This can be due to one of the following reasons

(1) Your CF card does not support creating additional partitions. In this
case use RAM-REG mode instead of RAM mode. RAM-REG does not need an
additional partition to store configuration information.
(2) Your CF supports additional partitions but you did not leave enough
unpartitioned space on your disk. This is necessary to allow EWF setup to
create its custom partition. For RAM mode , few mega bytes of
unpartitioned
space is sufficient.

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-S/embeddedwindowseefs/threads/


Korben said:
Hi all,

Embedded system is running with a Icop panel pc cpu vortex pdx-057T. The
image was builded with Xpe FP2007 with Xpe Rollup1,Rollup1Api on 4giga
ntfs
Lexar Cf
Here the end of the fba log.
I suspected the bloody ewf configuration.
In the setting of the ewf filter, the check box "start ewf enable" was
clear.
ewfmgr c: is not functioning.

Tks vm to contribute


14:04:15 PM - ConfigureEwf() Start.
14:04:15 PM - Getting EWF config parameters from registry.
14:04:15 PM - Non El Torito disk configuration.
14:04:15 PM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1.
14:04:15 PM - Protected Volume Config #0 :
14:04:15 PM - Disk= 0,Part= 1,Type= RAM.
14:04:15 PM - Enable= Disabled, Optimize= 0, LazyWrite= N.
14:04:15 PM - Found 1 Hard Disks.
14:04:15 PM - Disk #0 layout info:
14:04:15 PM - PRIMARY partition,start=0x0000000000007e00,
len=0x00000000eec1d000, type= 7
14:04:15 PM - Can't create EWF partition size = 0x000000000000fc00 on
disk# 0.
14:04:15 PM - Failed to create EWF partition.
14:04:15 PM - ConfigureEwf() End, status = 0x80070057.
14:04:15 PM - [CallEntryPointThread] C:\WINDOWS\system32\ewfdll.dll,
ConfigureEwf
14:04:15 PM - [FBASetProgressText] Resetting Setup Flag...
14:05:08 PM - [FBADoProperShutdown] Sleeping...
14:05:18 PM - [FBADoProperShutdown] Rebooting system...
Click to expand...
Click to expand...
 
Could you please elaborate your reboot problem ? It looks like you are
hitting a bluescreen which is causing a reboot . To analyze the bluescreen
you need to connect a kernel debugger to the machine. If you have done that
please share the output of "!analyze -v"

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-US/embeddedwindowseefs/threads/


Korben said:
Hi Srikanth,

You right, i left 1 giga on my unpartitioned free space Cf and then ewf
works.
But i'm still fighting with my reboot system.
Thk vm.


"Srikanth Kamath [MSFT]" <[email protected]> a
écrit dans le message de (e-mail address removed)...
From the log it appears that EWF was not able to create the EWF partition.
This can be due to one of the following reasons

(1) Your CF card does not support creating additional partitions. In this
case use RAM-REG mode instead of RAM mode. RAM-REG does not need an
additional partition to store configuration information.
(2) Your CF supports additional partitions but you did not leave enough
unpartitioned space on your disk. This is necessary to allow EWF setup to
create its custom partition. For RAM mode , few mega bytes of
unpartitioned
space is sufficient.

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-S/embeddedwindowseefs/threads/


Korben said:
Hi all,

Embedded system is running with a Icop panel pc cpu vortex pdx-057T. The
image was builded with Xpe FP2007 with Xpe Rollup1,Rollup1Api on 4giga
ntfs
Lexar Cf
Here the end of the fba log.
I suspected the bloody ewf configuration.
In the setting of the ewf filter, the check box "start ewf enable" was
clear.
ewfmgr c: is not functioning.

Tks vm to contribute


14:04:15 PM - ConfigureEwf() Start.
14:04:15 PM - Getting EWF config parameters from registry.
14:04:15 PM - Non El Torito disk configuration.
14:04:15 PM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1.
14:04:15 PM - Protected Volume Config #0 :
14:04:15 PM - Disk= 0,Part= 1,Type= RAM.
14:04:15 PM - Enable= Disabled, Optimize= 0, LazyWrite= N.
14:04:15 PM - Found 1 Hard Disks.
14:04:15 PM - Disk #0 layout info:
14:04:15 PM - PRIMARY partition,start=0x0000000000007e00,
len=0x00000000eec1d000, type= 7
14:04:15 PM - Can't create EWF partition size = 0x000000000000fc00 on
disk# 0.
14:04:15 PM - Failed to create EWF partition.
14:04:15 PM - ConfigureEwf() End, status = 0x80070057.
14:04:15 PM - [CallEntryPointThread] C:\WINDOWS\system32\ewfdll.dll,
ConfigureEwf
14:04:15 PM - [FBASetProgressText] Resetting Setup Flag...
14:05:08 PM - [FBADoProperShutdown] Sleeping...
14:05:18 PM - [FBADoProperShutdown] Rebooting system...
Click to expand...
Click to expand...
Click to expand...
 
Can you share teh Bluescreen number?

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
Book Author - XP Embedded Advanced, XP Embedded Supplemental Toolkit

Srikanth Kamath said:
Could you please elaborate your reboot problem ? It looks like you are
hitting a bluescreen which is causing a reboot . To analyze the bluescreen
you need to connect a kernel debugger to the machine. If you have done that
please share the output of "!analyze -v"

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-US/embeddedwindowseefs/threads/


Korben said:
Hi Srikanth,

You right, i left 1 giga on my unpartitioned free space Cf and then ewf
works.
But i'm still fighting with my reboot system.
Thk vm.


"Srikanth Kamath [MSFT]" <[email protected]> a
écrit dans le message de (e-mail address removed)...
From the log it appears that EWF was not able to create the EWF partition.
This can be due to one of the following reasons

(1) Your CF card does not support creating additional partitions. In this
case use RAM-REG mode instead of RAM mode. RAM-REG does not need an
additional partition to store configuration information.
(2) Your CF supports additional partitions but you did not leave enough
unpartitioned space on your disk. This is necessary to allow EWF setup to
create its custom partition. For RAM mode , few mega bytes of
unpartitioned
space is sufficient.

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-S/embeddedwindowseefs/threads/


:

Hi all,

Embedded system is running with a Icop panel pc cpu vortex pdx-057T. The
image was builded with Xpe FP2007 with Xpe Rollup1,Rollup1Api on 4giga
ntfs
Lexar Cf
Here the end of the fba log.
I suspected the bloody ewf configuration.
In the setting of the ewf filter, the check box "start ewf enable" was
clear.
ewfmgr c: is not functioning.

Tks vm to contribute


14:04:15 PM - ConfigureEwf() Start.
14:04:15 PM - Getting EWF config parameters from registry.
14:04:15 PM - Non El Torito disk configuration.
14:04:15 PM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1.
14:04:15 PM - Protected Volume Config #0 :
14:04:15 PM - Disk= 0,Part= 1,Type= RAM.
14:04:15 PM - Enable= Disabled, Optimize= 0, LazyWrite= N.
14:04:15 PM - Found 1 Hard Disks.
14:04:15 PM - Disk #0 layout info:
14:04:15 PM - PRIMARY partition,start=0x0000000000007e00,
len=0x00000000eec1d000, type= 7
14:04:15 PM - Can't create EWF partition size = 0x000000000000fc00 on
disk# 0.
14:04:15 PM - Failed to create EWF partition.
14:04:15 PM - ConfigureEwf() End, status = 0x80070057.
14:04:15 PM - [CallEntryPointThread] C:\WINDOWS\system32\ewfdll.dll,
ConfigureEwf
14:04:15 PM - [FBASetProgressText] Resetting Setup Flag...
14:05:08 PM - [FBADoProperShutdown] Sleeping...
14:05:18 PM - [FBADoProperShutdown] Rebooting system...
Click to expand...
Click to expand...
Click to expand...
 
Hi all,

I didn t get blue screen of death when the device rebooted, neither a dump
in \windows\Minidump.
Maybe the setting in the bios with th Cf (Pci ide bus master: enable or
desable ??)
Regards.


Sean Liming said:
Can you share teh Bluescreen number?

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
Book Author - XP Embedded Advanced, XP Embedded Supplemental Toolkit

Srikanth Kamath said:
Could you please elaborate your reboot problem ? It looks like you are
hitting a bluescreen which is causing a reboot . To analyze the
bluescreen
you need to connect a kernel debugger to the machine. If you have done
that
please share the output of "!analyze -v"

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-US/embeddedwindowseefs/threads/


Korben said:
Hi Srikanth,

You right, i left 1 giga on my unpartitioned free space Cf and then ewf
works.
But i'm still fighting with my reboot system.
Thk vm.


"Srikanth Kamath [MSFT]" <[email protected]>
a
écrit dans le message de (e-mail address removed)...
From the log it appears that EWF was not able to create the EWF
partition.
This can be due to one of the following reasons

(1) Your CF card does not support creating additional partitions. In
this
case use RAM-REG mode instead of RAM mode. RAM-REG does not need an
additional partition to store configuration information.
(2) Your CF supports additional partitions but you did not leave
enough
unpartitioned space on your disk. This is necessary to allow EWF
setup to
create its custom partition. For RAM mode , few mega bytes of
unpartitioned
space is sufficient.

Thanks
Srikanth
--
For questions on EWF, HORM and other EEFs - use our MSDN EEF forum
http://social.msdn.microsoft.com/forums/en-S/embeddedwindowseefs/threads/


:

Hi all,

Embedded system is running with a Icop panel pc cpu vortex pdx-057T.
The
image was builded with Xpe FP2007 with Xpe Rollup1,Rollup1Api on
4giga
ntfs
Lexar Cf
Here the end of the fba log.
I suspected the bloody ewf configuration.
In the setting of the ewf filter, the check box "start ewf enable"
was
clear.
ewfmgr c: is not functioning.

Tks vm to contribute


14:04:15 PM - ConfigureEwf() Start.
14:04:15 PM - Getting EWF config parameters from registry.
14:04:15 PM - Non El Torito disk configuration.
14:04:15 PM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes
= 1.
14:04:15 PM - Protected Volume Config #0 :
14:04:15 PM - Disk= 0,Part= 1,Type= RAM.
14:04:15 PM - Enable= Disabled, Optimize= 0, LazyWrite= N.
14:04:15 PM - Found 1 Hard Disks.
14:04:15 PM - Disk #0 layout info:
14:04:15 PM - PRIMARY partition,start=0x0000000000007e00,
len=0x00000000eec1d000, type= 7
14:04:15 PM - Can't create EWF partition size = 0x000000000000fc00
on
disk# 0.
14:04:15 PM - Failed to create EWF partition.
14:04:15 PM - ConfigureEwf() End, status = 0x80070057.
14:04:15 PM - [CallEntryPointThread]
C:\WINDOWS\system32\ewfdll.dll,
ConfigureEwf
14:04:15 PM - [FBASetProgressText] Resetting Setup Flag...
14:05:08 PM - [FBADoProperShutdown] Sleeping...
14:05:18 PM - [FBADoProperShutdown] Rebooting system...
Click to expand...
Click to expand...
Click to expand...
 
Back
Top