what causes disk errors when coming out of standby ?

  • Thread starter Thread starter MushroomNZ
  • Start date Start date
M

MushroomNZ

XP SP3

4 disk errors show up, all in one second of each other.
no other disk as slave on this channel.
I dont ever get disk errors at other times except for after standby.

i tried turning off hibernation, then
defrag, then turn it back on, still happens .


Event Type: Error
Event Source: Disk
Event Category: None
Event ID: 11
Date: 12/11/2009
Time: 4:53:27 AM
User: N/A
Computer: OEMPC
Description:
The driver detected a controller error on \Device\Harddisk0\D.


Data:
0000: 03 00 68 00 01 00 b6 00 ..h...¶.
0008: 00 00 00 00 0b 00 04 c0 .......À
0010: 03 01 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
0028: 31 96 03 00 00 00 00 00 1?......
0030: ff ff ff ff 07 00 00 00 ÿÿÿÿ....
0038: 40 00 00 00 00 00 00 00 @.......
0040: 00 20 0a 12 40 03 20 40 . ..@. @
0048: 00 00 00 00 0a 00 00 00 ........
0050: 00 20 57 05 38 a9 01 85 . W.8©.?
0058: 00 00 00 00 40 ab fb 84 ....@«û?
0060: 00 00 00 00 f7 49 99 0d ....÷I?.
0068: 28 00 0d 99 49 f7 00 00 (..?I÷..
0070: 08 00 00 00 00 00 00 00 ........
0078: 00 00 00 00 00 00 00 00 ........
0080: 00 00 00 00 00 00 00 00 ........
0088: 00 00 00 00 00 00 00 00 ........
 
What type of cable connects to the drive? Try another?

Another suggestion.Run a full surface scan with HD Tune to check for bad
sectors on the hard drive.

HD Tune only gives information and does not fix any problems.

Download and run it and see what it turns up. You want HD Tune
(freeware) version 2.55 not HD Tune Pro (not Freeware) version 3.00.
http://www.hdtune.com/

Select the Info tabs and place the cursor on the drive under Drive
letter and then double click the two page icon ( copy to Clipboard )
and copy into a further message.

Select the Health tab and then double click the two page icon ( copy to
Clipboard ) and copy into a further message. Make sure you do a full
surface scan with HD Tune.

--


Hope this helps.

Gerry
~~~~
FCA
Stourport, England
Enquire, plan and execute
~~~~~~~~~~~~~~~~~~~
 
cant see it being the cable, DMA access works fine.

HD showed damaged sectors at the end of the drive.
past where i am using it. no event recods came up during the scan.

here's the output :

HD Tune: WDC WD2500JS-00NCB1 Information

Firmware version : 10.02E02
Serial number : WD-WMANK3679176
Capacity : 232.9 GB (~250.1 GB)
Buffer size : 8192 KB
Standard : ATA/ATAPI-7 - SATA II
Supported mode : UDMA Mode 6 (Ultra ATA/133)
Current mode : UDMA Mode 6 (Ultra ATA/133)

S.M.A.R.T : yes
48-bit Address : yes
Read Look-Ahead : yes
Write Cache : yes
Host Protected Area : yes
Device Configuration Overlay : yes
Automatic Acoustic Management: yes
Power Management : yes
Advanced Power Management : no
Power-up in Standby : yes
Security Mode : yes
Firmware Upgradable : yes

Partition : 1
Drive letter : C:\
Label :
Capacity : 227992 MB
Usage : 70.72%
Type : FAT32
Bootable : Yes

Partition : 2
Drive letter :
Label :
Capacity : 10479 MB
Usage : 0.00%
Type : unknown (49h)
Bootable : No
HD Tune: WDC WD2500JS-00NCB1 Health

ID Current Worst ThresholdData
Status
(01) Raw Read Error Rate 200 200 51 0
Ok
(03) Spin Up Time 191 187 21 5408
Ok
(04) Start/Stop Count 99 99 0 1605
Ok
(05) Reallocated Sector Count 200 200 140 0
Ok
(07) Seek Error Rate 200 200 51 0
Ok
(09) Power On Hours Count 77 77 0 16957
Ok
(0A) Spin Retry Count 100 100 51 0
Ok
(0B) Calibration Retry Count 100 100 51 0
Ok
(0C) Power Cycle Count 99 99 0 1594
Ok
(BE) Airflow Temperature 61 44 45 39
Ok
(C2) Temperature 111 94 0 39
Ok
(C4) Reallocated Event Count 200 200 0 0
Ok
(C5) Current Pending Sector 200 200 0 0
Ok
(C6) Offline Uncorrectable 200 200 0 0
Ok
(C7) Ultra DMA CRC Error Count 200 200 0 1
Ok
(C8) Write Error Rate 200 200 51 0
Ok

Power On Time : 16957
Health Status : Ok
 
Back
Top