Vista will not recognize router

  • Thread starter Thread starter hlwlaw
  • Start date Start date
H

hlwlaw

I have an existing hardwired home network with 2 XP computers sharing
a DSL internet connection, printer, etc. I recently purchased an
additional computer that has Vista. When I tried to access this home
network, it does not seem to recognize the router. I have checked all
of the hardware and software connections that I know about, and no
success. I have run ipconfig on the main XP computer and the Vista
computer and found that the IP address for the two are different. The
XP looks good with 192.168.1.101 while the Vista is 169.254.136.129 I
also found the IP address of the router 192.168.1.1, I was able to
ping it with the XP computer, but the Vista computer gives an error
"transmit failed, error code 1231". The router is a LinkSys NR041
Cable/DSL 4-port Router.
 
please post the text output of

ipconfig /all

from the Vista computer

I have an existing hardwired home network with 2 XP computers sharing
a DSL internet connection, printer, etc. I recently purchased an
additional computer that has Vista. When I tried to access this home
network, it does not seem to recognize the router. I have checked all
of the hardware and software connections that I know about, and no
success. I have run ipconfig on the main XP computer and the Vista
computer and found that the IP address for the two are different. The
XP looks good with 192.168.1.101 while the Vista is 169.254.136.129 I
also found the IP address of the router 192.168.1.1, I was able to
ping it with the XP computer, but the Vista computer gives an error
"transmit failed, error code 1231". The router is a LinkSys NR041
Cable/DSL 4-port Router.
Click to expand...
--

Barb Bowman
MS Windows-MVP
http://www.microsoft.com/windowsxp/expertzone/meetexperts/bowman.mspx
http://blogs.digitalmediaphile.com/barb/
 
Here it is:
Windows IP Configuration

Host Name . . . . . . . . . . . . : HP-2007
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Home Network:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking
Controller
Physical Address. . . . . . . . . : 00-1D-60-B5-D0-0E
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . :
fe80::c129:1d35:3a84:8881%8(Preferred)
Autoconfiguration IPv4 Address. . : 169.254.136.129(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 201333756
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-0E-B9-5D-
A8-00-1D-60-B5-D0-0E
DNS Servers . . . . . . . . . . . : fe80::c129:1d35:3a84:8881%8
NetBIOS over Tcpip. . . . . . . . : Enabled

Tunnel adapter Local Area Connection* 6:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : isatap.{17C5E363-870A-4F81-9595-
E62F8165DE74}
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::5efe:
169.254.136.129%10(Preferred)
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : fe80::c129:1d35:3a84:8881%8
NetBIOS over Tcpip. . . . . . . . : Disabled

Tunnel adapter Local Area Connection* 7:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : 6TO4 Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Thanks
 
I can't find the NR041 on the Linksys support site so I can't tell
you if there have been firmware releases for this.

However, two things to try are:

http://support.microsoft.com/kb/928233/en-us

and unbinding IPv6

Here it is:
Windows IP Configuration

Host Name . . . . . . . . . . . . : HP-2007
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Home Network:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking
Controller
Physical Address. . . . . . . . . : 00-1D-60-B5-D0-0E
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . :
fe80::c129:1d35:3a84:8881%8(Preferred)
Autoconfiguration IPv4 Address. . : 169.254.136.129(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 201333756
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-0E-B9-5D-
A8-00-1D-60-B5-D0-0E
DNS Servers . . . . . . . . . . . : fe80::c129:1d35:3a84:8881%8
NetBIOS over Tcpip. . . . . . . . : Enabled

Tunnel adapter Local Area Connection* 6:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : isatap.{17C5E363-870A-4F81-9595-
E62F8165DE74}
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::5efe:
169.254.136.129%10(Preferred)
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : fe80::c129:1d35:3a84:8881%8
NetBIOS over Tcpip. . . . . . . . : Disabled

Tunnel adapter Local Area Connection* 7:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : 6TO4 Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Thanks
Click to expand...
--

Barb Bowman
MS Windows-MVP
http://www.microsoft.com/windowsxp/expertzone/meetexperts/bowman.mspx
http://blogs.digitalmediaphile.com/barb/
 
Barb Bowman said:
I can't find the NR041 on the Linksys support site so I can't tell
you if there have been firmware releases for this.

However, two things to try are:

http://support.microsoft.com/kb/928233/en-us

and unbinding IPv6


--

Barb Bowman
MS Windows-MVP
http://www.microsoft.com/windowsxp/expertzone/meetexperts/bowman.mspx
http://blogs.digitalmediaphile.com/barb/
Click to expand...

The NR041 not on the Linksys site because its not a regular Linksys product.
I have one of those, but don't use it any longer. I don't believe the
firmware has ever been updated past what is on the support pages.

http://www.networkeverywhere.com/support/routersupport.asp#firmware

--

Al Jarvi (MS-MVP Windows Networking)

Please post *ALL* questions and replies to the news group for the
mutual benefit of all of us...
The MS-MVP Program - http://mvp.support.microsoft.com
This posting is provided "AS IS" with no warranties, and confers no
rights...
 
it isn't on the compatible with Vista list.
http://winqual.microsoft.com/HCL/ProductList.aspx?m=v&cid=712&g=d

The NR041 not on the Linksys site because its not a regular Linksys product.
I have one of those, but don't use it any longer. I don't believe the
firmware has ever been updated past what is on the support pages.

http://www.networkeverywhere.com/support/routersupport.asp#firmware
Click to expand...
--

Barb Bowman
MS Windows-MVP
http://www.microsoft.com/windowsxp/expertzone/meetexperts/bowman.mspx
http://blogs.digitalmediaphile.com/barb/
 
Barb Bowman said:
it isn't on the compatible with Vista list.
http://winqual.microsoft.com/HCL/ProductList.aspx?m=v&cid=712&g=d


--

Barb Bowman
MS Windows-MVP
http://www.microsoft.com/windowsxp/expertzone/meetexperts/bowman.mspx
http://blogs.digitalmediaphile.com/barb/
Click to expand...

Not surprising since its pretty old...

--

Al Jarvi (MS-MVP Windows Networking)

Please post *ALL* questions and replies to the news group for the
mutual benefit of all of us...
The MS-MVP Program - http://mvp.support.microsoft.com
This posting is provided "AS IS" with no warranties, and confers no
rights...
 
Hi,

Can you be a bit more specific as to how the computers and printer are
interconnected. Specifically, are the computers independently connected to
the router, and if so which port numbers are they connected to. I am assuming
that the ports have addresses 192.168.1.101-104. Check that the port
connected to your Vista machine is actually enabled in your router. If not,
then enable it through the router interface. You will have to do this from
your XP machine. Once you have ensured that the port is enabled, check to see
if Vista can connect to the Internet. If not, then you might need to set the
IP address manually in Vista - if connected to port #3, for example, then you
will need to set the IP address to 192.168.1.103.
Dwarf
 
Thank you for the help.
I decided to purchase a new router, and now everything works fine with
the home network. Of course there has to be a but...
But now I cannot get the router to access the internet. Working on
it, hopefully all is well.
 
typically you have to power cycle your broadband modem when you
connect a new router (OR you have to find the mac address of the old
router and manually enter it into a field in the new router - this
happens when your provider registers the mac address and pairs it
with the broadband modem). what router did you purchase?

Thank you for the help.
I decided to purchase a new router, and now everything works fine with
the home network. Of course there has to be a but...
But now I cannot get the router to access the internet. Working on
it, hopefully all is well.
Click to expand...
--

Barb Bowman
MS Windows-MVP
http://www.microsoft.com/windowsxp/expertzone/meetexperts/bowman.mspx
http://blogs.digitalmediaphile.com/barb/
 
Back
Top