G
Guest
-----------------------------
Hi there..
setup :
Telsey CPVA 500 router (adsl provider Tele2 in spain)
DLink DWL-G700AP access point
Asus X51R laptop with Vista Home Premium (pre-installed):Atheros AR5006EG
wireless network adaptor
1.I can connect the laptop to the router directly via ethernet cable without
problem.
2. Other laptops with XP can connect wirelessly with no problem (WEP
activated)
3. I cannot connect the laptop to the Access point above. I can connect to
other wifi networks but not this one. When i try to connect i get the error
message:
Root cause:
Windows cannot connect to "blackhorse"
Wireless association failed due to an unknown reason.
Detailed root cause:
802.11 connection failed due to status code 1: unspecified failure
It´s like it doesn´t even attempt to connect. Straight to the above
message..no connection bar and no WEP key prompt. (I have tried both
open/disabled and WEP activated..same result.)
I´ve turned off ant-virus before all this. Firewall aswell.
I´ve tried fixed IP on laptop.
Wireless adaptor uninstalled and re-installed with up to date drivers.
Access point firmware is up to date.
I´ve reset the AP . Started again. still same result.
The router I cannot access because Tele2 have prevented it. which is
ridiculous but seeing as i can connect with cable ok I´m assuming the problem
isn´t there.
I´ve spoken to Dlink ..they say no problem with their product and Vista.
It´s the configuration of the laptop they say...?
I can´t think of what else to do. I´d like to try a different access point
with this router but haven´t one available and I can walk outside and connect
to a different network no probs...
is there something i haven´t tried? Why just this laptop and this network?
if not i´ll have to uninstall Vista and go back to XP .
any help would be much appreciated.
neil
event report below..
Log Name: System
Source: Microsoft-Windows-Diagnostics-Networking
Date: 19/03/2007 23:10:23
Event ID: 6100
Task Category: (12)
Level: Information
Keywords: (2)
User: LOCAL SERVICE
Computer: deano-PC
Description:
Helper Class (RNWF MSM Helper Class) Event:
Wireless Diagnostic Helper Class Event
For complete information about this session see the Wireless Diagnostic
Informational Event.
Helper Class: Native WiFi MSM
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 2bd302b4-0d6e-417e-b56f-9cbf93922255
Interface name: Atheros AR5006EG Wireless Network Adapter
Interface type: Native WiFi
Profile: Discovery connection
SSID: blackhorse
SSID length: 10
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Root cause:
Windows cannot connect to "blackhorse"
Wireless association failed due to an unknown reason.
Detailed root cause:
802.11 connection failed due to status code 1: unspecified failure
Repair option:
Try connecting to "blackhorse" again
If the problem continues, contact your network administrator or hardware
manufacturer for further assistance.
Event Verbosity:0
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Diagnostics-Networking"
Guid="{36c23e18-0e66-11d9-bbeb-505054503030}" />
<EventID>6100</EventID>
<Version>0</Version>
<Level>4</Level>
<Task>12</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000002</Keywords>
<TimeCreated SystemTime="2007-03-19T22:10:23.148Z" />
<EventRecordID>4855</EventRecordID>
<Correlation ActivityID="{7B37C63F-1246-4161-BC74-BA63755B8719}" />
<Execution ProcessID="3588" ThreadID="5332" />
<Channel>System</Channel>
<Computer>deano-PC</Computer>
<Security UserID="S-1-5-19" />
</System>
<EventData>
<Data Name="HelperClassName">RNWF MSM Helper Class</Data>
<Data Name="EventDescription">Wireless Diagnostic Helper Class Event
For complete information about this session see the Wireless Diagnostic
Informational Event.
Helper Class: Native WiFi MSM
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 2bd302b4-0d6e-417e-b56f-9cbf93922255
Interface name: Atheros AR5006EG Wireless Network Adapter
Interface type: Native WiFi
Profile: Discovery connection
SSID: blackhorse
SSID length: 10
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Root cause:
Windows cannot connect to "blackhorse"
Wireless association failed due to an unknown reason.
Detailed root cause:
802.11 connection failed due to status code 1: unspecified failure
Repair option:
Try connecting to "blackhorse" again
If the problem continues, contact your network administrator or hardware
manufacturer for further assistance.
</Data>
<Data Name="EventVerbosity">0</Data>
</EventData>
</Event>
Hi there..
setup :
Telsey CPVA 500 router (adsl provider Tele2 in spain)
DLink DWL-G700AP access point
Asus X51R laptop with Vista Home Premium (pre-installed):Atheros AR5006EG
wireless network adaptor
1.I can connect the laptop to the router directly via ethernet cable without
problem.
2. Other laptops with XP can connect wirelessly with no problem (WEP
activated)
3. I cannot connect the laptop to the Access point above. I can connect to
other wifi networks but not this one. When i try to connect i get the error
message:
Root cause:
Windows cannot connect to "blackhorse"
Wireless association failed due to an unknown reason.
Detailed root cause:
802.11 connection failed due to status code 1: unspecified failure
It´s like it doesn´t even attempt to connect. Straight to the above
message..no connection bar and no WEP key prompt. (I have tried both
open/disabled and WEP activated..same result.)
I´ve turned off ant-virus before all this. Firewall aswell.
I´ve tried fixed IP on laptop.
Wireless adaptor uninstalled and re-installed with up to date drivers.
Access point firmware is up to date.
I´ve reset the AP . Started again. still same result.
The router I cannot access because Tele2 have prevented it. which is
ridiculous but seeing as i can connect with cable ok I´m assuming the problem
isn´t there.
I´ve spoken to Dlink ..they say no problem with their product and Vista.
It´s the configuration of the laptop they say...?
I can´t think of what else to do. I´d like to try a different access point
with this router but haven´t one available and I can walk outside and connect
to a different network no probs...
is there something i haven´t tried? Why just this laptop and this network?
if not i´ll have to uninstall Vista and go back to XP .
any help would be much appreciated.
neil
event report below..
Log Name: System
Source: Microsoft-Windows-Diagnostics-Networking
Date: 19/03/2007 23:10:23
Event ID: 6100
Task Category: (12)
Level: Information
Keywords: (2)
User: LOCAL SERVICE
Computer: deano-PC
Description:
Helper Class (RNWF MSM Helper Class) Event:
Wireless Diagnostic Helper Class Event
For complete information about this session see the Wireless Diagnostic
Informational Event.
Helper Class: Native WiFi MSM
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 2bd302b4-0d6e-417e-b56f-9cbf93922255
Interface name: Atheros AR5006EG Wireless Network Adapter
Interface type: Native WiFi
Profile: Discovery connection
SSID: blackhorse
SSID length: 10
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Root cause:
Windows cannot connect to "blackhorse"
Wireless association failed due to an unknown reason.
Detailed root cause:
802.11 connection failed due to status code 1: unspecified failure
Repair option:
Try connecting to "blackhorse" again
If the problem continues, contact your network administrator or hardware
manufacturer for further assistance.
Event Verbosity:0
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Diagnostics-Networking"
Guid="{36c23e18-0e66-11d9-bbeb-505054503030}" />
<EventID>6100</EventID>
<Version>0</Version>
<Level>4</Level>
<Task>12</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000002</Keywords>
<TimeCreated SystemTime="2007-03-19T22:10:23.148Z" />
<EventRecordID>4855</EventRecordID>
<Correlation ActivityID="{7B37C63F-1246-4161-BC74-BA63755B8719}" />
<Execution ProcessID="3588" ThreadID="5332" />
<Channel>System</Channel>
<Computer>deano-PC</Computer>
<Security UserID="S-1-5-19" />
</System>
<EventData>
<Data Name="HelperClassName">RNWF MSM Helper Class</Data>
<Data Name="EventDescription">Wireless Diagnostic Helper Class Event
For complete information about this session see the Wireless Diagnostic
Informational Event.
Helper Class: Native WiFi MSM
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 2bd302b4-0d6e-417e-b56f-9cbf93922255
Interface name: Atheros AR5006EG Wireless Network Adapter
Interface type: Native WiFi
Profile: Discovery connection
SSID: blackhorse
SSID length: 10
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Root cause:
Windows cannot connect to "blackhorse"
Wireless association failed due to an unknown reason.
Detailed root cause:
802.11 connection failed due to status code 1: unspecified failure
Repair option:
Try connecting to "blackhorse" again
If the problem continues, contact your network administrator or hardware
manufacturer for further assistance.
</Data>
<Data Name="EventVerbosity">0</Data>
</EventData>
</Event>