System Restore can no longer resolve this issue as the restore points are
corrupt. System Restore itself can be fixed by turning it off, rebooting
and turning it back on. This will wipe all current restore points up to the
time of this operation but you will be able to create new restore points
which should once again work though they can't solve your current problem.
To deal with your current problem, you are going to need to do some
sleuthing on your own. If the problem is system DLLs, system file check or
a repair install might resolve the issue. If the DLLs belong to other
applications perhaps reinstalling them will resolve the issue or you might
need updates for those applications in which case you would have to check
the app creator's website.
The following are things you can do to try to source the issue:
First, be sure your antivirus software has the latest definitions and run a
virus scan.
Second, download, install and run Ad Aware:
www.lavasoftusa.com
Note: you should always be well backed up before running an application of
this type.
If your system is clear of viruses, open Control Panel, open System, go to
the Advanced tab, click Settings under Startup and Recovery, remove the
check from "Automatically Restart" under System Failure. This will cause
the system to blue screen instead of restarting on errors and the
information on the blue screen may give a clue as to the source of the
issue.
Open Control Panel, open Administrative Tools, open Event Viewer, look for
errors corresponding to the crash, double click the error, the information
contained within may give a clue as to the
source of the problem. If you don't understand the information inside, the
third button down in that dialog box will copy the information,
you can then paste it into a message and post it here and maybe we can
figure out what is going on.
Assuming you have an XP CD and not a recovery CD, place the XP CD in the
drive, when the setup screen appears, select "Check System Compatibility,"
the report it generates may point to problem hardware or software on your
system. If you do not have an XP CD, you can download this application
known as the Upgrade Advisor from the following site:
http://www.microsoft.com/windowsxp/pro/howtobuy/upgrading/advisor.asp
Note: If you have access to a broadband connection it might be best to
download using that as this is a rather large download.
Check for the latest drivers for your hardware, especially your graphics
card and soundcard and all peripherals connected to your system. Do not use
Windows Update for this, go to the device manufacturer's web sites and if
you install updated drivers, ignore the message about drivers being unsigned
by Microsoft. *Before installing any drivers, be sure you are well backed
up and it's probably a good idea to manually create a restore point in
System Restore in case you have problems as a result of the driver update
and note, System Restore is not a substitute for a backup. Start\All
Programs\Accessories\System Tools\System Restore
Below are the procedures for System File Checker and System Restore:
The following assumes you have an actual XP CD as opposed to a restore CD or
restore partition supplied by your PC manufacturer.
Go to Start, type sfc /scannow in the run box and press enter. Note, there
is a space between sfc and the forward slash. You will be asked for your XP
CD. Be aware, upon inserting the CD the XP setup screen may appear, this is
not a part of sfc /scannow, rather it is being invoked by autorun. Simply
minimize the screen and allow sfc to continue.
If the above fails to resolve the issue, try a repair install as follows:
Be sure you are well backed up in case there is a problem from which you are
unable to recover. NOTE, while a repair install should leave your data
files intact, if something goes wrong during the repair install, you may be
forced to start over and do a clean install of XP. If you don't have your
data backed up, you would lose your data should that eventuality occur.
Assuming your system is set to boot from the CD-ROM drive, boot with the XP
CD in the drive. If it isn't or you are not sure, you need to enter the
system's BIOS. When you boot the system, the first screen usually has
instructions that if you wish to enter setup press a specific key, when you
see that, do so. Then you will have to navigate to the boot sequence, if
the CD-ROM drive is not first line, set it first in the boot sequence. Save
your settings and exit with the XP CD in the drive. The system will reboot.
Boot from the CD. If your system is set to be able to boot from the CD, it
should detect the disk and give a brief message, during the boot up, if you
wish to boot from the CD press any key.
Once you have pressed a key, setup should begin. You will see a reference
asking if you need to load special drivers and another notice that if you
wish to begin the ASR (Automatic Recovery Console) depress F2. Just let
setup run past all of that. It will continue to load files and drivers.
Then it will bring you to a screen. Eventually, you will come to a screen
with the option to (1) setup Windows or (2) Repair Windows Installation
using the Recovery console.
The first option, to setup Windows is the one you want and requires you to
press enter. When asked, press F8 to accept the end user agreement. Setup
will then search for previous versions of Windows. Upon finding your
version, it will ask if you wish to Repair your current installation or
install fresh. Press R, that will run a repair installation. From there
on, follow the screens.
