STOP error STOP: 0x0000007B (0x81896E50, 0xC0000032, 0x00000000, 0x0000000

  • Thread starter Thread starter jim
  • Start date Start date
J

jim

Hi,
I got the above error when I turned my machine on
yesterday with a blue screen. I went to several sites and
researched it. some causes were removal of components that
mesed up other files. That wasnt my problem. I think the
problem is the IDe controllers and the PnP ws somehow
knocked out ot the registry. I downloaded all the
motherboard drivers I could but couldnt load any because
they wont load in DOS. I also did a complete scan with
scandisk and with the seagate utility which is supposed to
fix everything if its the harddisk.
I tried to make a set of bootdisks from the CD-RM but got
and error
Cannot find File CDBOOT1.
" CDBOOT2.
Cannot find File CDBOOT3.
Cannot find File CDBOOT4.
AFTER i INPUT
BOOTDISK\MAKEDISK A:
I went into BIOS and reset them both to optimize and then
to default but that didnt do any good. I also went into
safe mode and tried reloading last configuration and
everything else but tht didnt do anything either.
If anybody has any ideas please help because I have
exahausted my resources.
thanks
(e-mail address removed)
 
Hi,
I got the above error when I turned my machine on
yesterday with a blue screen. I went to several sites and
researched it. some causes were removal of components that
mesed up other files. That wasnt my problem. I think the
problem is the IDe controllers and the PnP ws somehow
knocked out ot the registry. I downloaded all the
motherboard drivers I could but couldnt load any because
they wont load in DOS. I also did a complete scan with
scandisk and with the seagate utility which is supposed to
fix everything if its the harddisk.
I tried to make a set of bootdisks from the CD-RM but got
and error
Cannot find File CDBOOT1.
" CDBOOT2.
Cannot find File CDBOOT3.
Cannot find File CDBOOT4.
AFTER i INPUT
BOOTDISK\MAKEDISK A:
I went into BIOS and reset them both to optimize and then
to default but that didnt do any good. I also went into
safe mode and tried reloading last configuration and
everything else but tht didnt do anything either.
If anybody has any ideas please help because I have
exahausted my resources.
thanks
(e-mail address removed)
Click to expand...

The documented possibilities are:

http://support.microsoft.com?kbid=122926 "Troubleshooting Stop 0x0000007B or
'0x4000' Error"
http://support.microsoft.com?kbid=822052 "How to troubleshoot 'Stop 0x0000007B'
error messages in Windows 2000"
http://support.microsoft.com?kbid=178558 "Upgrade Installation of Windows NT on
HP NetServer Generates Error Event ID 7026"
http://support.microsoft.com?kbid=226361 "Error Code '[0x4 0x1 0 0]' During
Windows 2000 Setup"
http://support.microsoft.com?kbid=241827 "Mass Storage Device May Not Be Started
During Unattended Setup"
http://support.microsoft.com?kbid=246043 "No Mouse or Keyboard Response at Logon
Prompt After Installing IomegaWare"
http://support.microsoft.com?kbid=268066 "Startup Problems When Transferring
System Hard Disk to a Backup Computer"
http://support.microsoft.com?kbid=300224 "'Stop 0x0000001E
KMODE_EXCEPTION_NOT_HANDLED' Error Message May Be Displayed When You Use the
Diskperf Utility"
http://support.microsoft.com?kbid=822051 "How to troubleshoot 'Stop 0x0000007B'
error messages that occur when you run Windows 2000 Setup"
http://support.microsoft.com?kbid=826901 "'Stop 0x0000007B' error message after
you remove Dell OpenManage software in Windows 2000 Server"


Jerold Schulman
Windows: General MVP
JSI, Inc.
http://www.jsiinc.com
 
Back
Top