Stop Error 0x0000007b

  • Thread starter Thread starter Louis LeBrun
  • Start date Start date
L

Louis LeBrun

I'm trying to install Vista Beta 2, I have downloaded the iso file and
burned a DVD. I'm installing using Windows XP on a 20 gb logical partition
on the same drive as Windows XP (C partition). The installation goes well
until the first reboot. Then I get the following message:
A problem has been detected and windows has been shut down to prevent
damage to your computer. If this is the first time you've seen this stop
error screen, restart your computer. If the screen appears again, follow
these steps: check for viruseson your computer. Remove any newly installed
hard drives or hard drive controllers. Check your hard drive to make sure it
is properly configured and terminated. Run chdksk /F to check for hard drive
corruption, and then restart your computer.
Tech information
STOP: 0x0000007B (0x81006BB0,0x00000034, 0x00000000,0x00000000)
I have run a virus scan - no viruses found, I have run chkdsk and no
problems found, I have not installed any new hard drives or hard drive
controllers, and since Windows XP runs, I'm sure the hard drive is properly
configured and terminated (what ever that means).
My system consists of an ASUS P5VDC-Mx motherboard, a Intel Pentium D 2.66
GHz CPU, 1 kb of ram, a 160 GB SATA hard drive, and a Nvidia GeForce 6200
video card.
Any help will be appreciated.

Respectfully,
Louis LeBrun
 
Are you installing to a RAID array or SATA? I had the same problem w/ my
RAID setup, the Vista install won't detect ANY of the dirvers I have for it
on ANY form of media.

I ended up installing it on my IDE drive being forced to change my boot
drive in BIOS whenever I want to boot a different OS. I can't find info
anywhere on pointing the new boot loader to a different device in the system,
only ways to point to diferent patitions on the same drive.


Drew
 
The 7b error can be caused by various things. One quite common is some kind
of IDE driver issue.

First I would recommend to try changing SATA settings in BIOS if possible
and see if that makes a difference.
If you happen to have spare PATA drives somewhere, try installing on one of
those too. It might use a different chip on the motherboard and thus help
avoid the 7b error.

The bios often have SATA Enchanced, legacy, compatibility, raid or such
modes.. Try one that doesn't say anything or says legacy or compatibility.
 
I'm installing SATA. I have no RAID array.
I tried installing Vista on as second IDE hard drive and got the same
results. (I did not remove the SATA drive, I just added a second drive.)

Lou

DrDrew said:
Are you installing to a RAID array or SATA? I had the same problem w/ my
RAID setup, the Vista install won't detect ANY of the dirvers I have for
it
on ANY form of media.

I ended up installing it on my IDE drive being forced to change my boot
drive in BIOS whenever I want to boot a different OS. I can't find info
anywhere on pointing the new boot loader to a different device in the
system,
only ways to point to diferent patitions on the same drive.


Drew
Click to expand...
<Snip>
 
There is no options in the BIOS to change any SATA settings. I have added a
second IDE hard drive and got the same results.

Lou

droid said:
The 7b error can be caused by various things. One quite common is some
kind of IDE driver issue.

First I would recommend to try changing SATA settings in BIOS if possible
and see if that makes a difference.
If you happen to have spare PATA drives somewhere, try installing on one
of those too. It might use a different chip on the motherboard and thus
help avoid the 7b error.

The bios often have SATA Enchanced, legacy, compatibility, raid or such
modes.. Try one that doesn't say anything or says legacy or compatibility.
Click to expand...
<Snip>
 
If XP still works, run pci32.exe >output.txt and paste its output to here.

http://members.net-tech.com.au/dft0802/downloads.htm

It's not immediate remedy but might help fixing the issue.. in the long
run..
Also google -> beta client (http://go.microsoft.com/fwlink/?LinkId=43655)
The first link should be Microsoft link. It needs .NET but I think it will
be installed if you try to run it without it..
When you report a bug with it, it'll include hardware info to MS. The more
people reporting this error the likely they'll do something.
 
Quite a few unknown devices..

You did download the updated
http://members.net-tech.com.au/dft0802/downloads/pcidevs.txt
file before running? I forgot to mention about that.. :-(

Also more information may come with -R switch since it looks like you have 2
pci express root thingies..
This is what it says on the download page:

"- Keeping up with modern hardware - with full PCI Express and multiple
root-bus support via the -R option, PCI32 outperforms older tools tenfold"

So it may be needed to use the -R to find out devices under the PCIe roots
.... Give it a try if you like and see if there's more output this way.
 
Hi all,

Just wanted to share my experiences with you, in hopes of finding a
resolution to this most annoying prblem...

I too get the BSOD after first reboot in Vista install. It seems that the
general concensus is that 7B is Vista not liking something on the IDE bus.
So, I unplugged the ONLY IDE drive from the mobo (Pioneer DVR-109), and
disabled all IDE channels in the BIOS. I then rebooted, and deleted all the
files that Vista had written to my XP partition (C: ), copied the Vista DVD
to the partition I want to install it on (D: ), and ran setup from the hard
drive, which by the way, is 2 WD 740 GD's in RAID 0 on Nvidia SATA ports 3
and 4. So there are NO IDE devices AT ALL.

And guess what? Still got the 7B stop error.

I tried booting in safe mode, to finish the install, I disabled driver sig
checking, enabled boot logging, none having the desired effect of allowing
Vista to finish installing.

I will attach pci32's report in its entirety, in hopes that someone will see
what I have been unable to see.

Report-Date = 23-06-2006 (D-M-Y)


PC-Model =


=== F u l l R e p o r t ================================================



Bus 0 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Eh nForce4 Memory Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Memory, type Other
New Capabilities List Present:
HyperTransport Capability
SubType : Slave/Primary Interface
Base UnitID : 0
UnitID Count : 15
HyperTransport Capability
SubType : MSI Mapping

Bus 0 (PCI Express), Device Number 1, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0050h nForce4 PCI to ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp

Bus 0 (PCI Express), Device Number 1, Device Function 1
Vendor 10DEh Nvidia Corp
Device 0052h nForce4 SMBus
Command 0001h (I/O Access)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type SMBus Controller
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 0000FC00h
Address 4 is an I/O Port : 00001C00h
Address 5 is an I/O Port : 00001C40h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ah nForce4 USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (OHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02F000h
System IRQ 22, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 1
Vendor 10DEh Nvidia Corp
Device 005Bh nForce4 USB 2.0 Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FEB00000h
System IRQ 20, INT# B
New Capabilities List Present:
USB 2.0 EHCI Debug Port Capability
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 6, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0053h nForce4 Parallel ATA Controller
Command 0005h (I/O Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 4 is an I/O Port : 0000F000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 7, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0054h nForce4 Serial ATA Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is in native mode at Addresses 0 & 1
Secondary Channel is in native mode at Addresses 2 & 3
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 000009F0h
Address 1 is an I/O Port : 00000BF0h
Address 2 is an I/O Port : 00000970h
Address 3 is an I/O Port : 00000B70h
Address 4 is an I/O Port : 0000DC00h
Address 5 is a Memory Address (anywhere in 0-4Gb) : FE02D000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 9, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ch nForce4 PCI Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A2h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 0204h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master
Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : None
Prefetchable Memory Range Passed to Secondary Bus : None

Bus 0 (PCI Express), Device Number 10, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0057h nForce4 Ethernet Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 01h, Maximum Bus Latency 14h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02C000h
Address 1 is an I/O Port : 0000D800h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 11, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 2
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000B000h to 0000BFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDD00000h to FDDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDC00000h to
00000000FDCFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Fatal Error Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : xReserved
Link Port Number : 3
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Link Training Error Reported!!
Slot Capabilities :
Slot Power Limit Value : 6.000 Watts
Physical slot Number 1

Bus 0 (PCI Express), Device Number 12, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus Number 3
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000A000h to 0000AFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDB00000h to FDBFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDA00000h to
00000000FDAFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x4
Link Port Number : 2
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Slot Capabilities :
Slot Power Limit Value : 4.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 13, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 4, Subordinate Bus Number 4
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00009000h to 00009FFFh (32-bit)
Memory Range Passed to Secondary Bus : FA000000h to FCFFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000D0000000h to
00000000DFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 2.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 14, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 5, Subordinate Bus Number 5
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00008000h to 00008FFFh (32-bit)
Memory Range Passed to Secondary Bus : F7000000h to F9FFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000C0000000h to
00000000CFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 0.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 24, Device Function 0
Vendor 1022h Advanced Micro Devices (AMD)
Device 1100h Athlon 64 / Opteron HyperTransport Technology Configuration
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
New Capabilities List Present:
HyperTransport Capability
SubType : Host/Secondary Interface

Bus 0 (PCI Express), Device Number 24, Device Function 1
Vendor 1022h Advanced Micro Devices (AMD)
Device 1101h Athlon 64 / Opteron Address Map
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 2
Vendor 1022h Advanced Micro Devices (AMD)
Device 1102h Athlon 64 / Opteron DRAM Controller
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 3
Vendor 1022h Advanced Micro Devices (AMD)
Device 1103h Athlon 64 / Opteron Miscellaneous Control
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 1 (PCI), Device Number 7, Device Function 0
Vendor 13F6h C-Media Electronics Inc
Device 0111h CMI8738/C3DX PCI Audio Device
Command 0085h (I/O Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 02h, Maximum Bus Latency 18h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 3741584Dh Unknown
Subsystem Vendor 584Dh Unknown
Address 0 is an I/O Port : 0000CC00h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 4 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : FA000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
D0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : FB000000h
Address 5 is an I/O Port : 00009C00h
System IRQ 19, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8

Bus 5 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0006h (Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
C0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : F8000000h
Address 5 is an I/O Port : 00008C80h
System IRQ 18, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8


IRQ Summary: IRQs 10,14,15,18,19,20,21,22,23 are used by PCI devices
Shared IRQs: IRQ 19 is shared by 2 PCI Devices

IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...


PCI Busses, Devices and Device Functions Tree

--Bus 0 (PCI Express)
|__Device 00h 10DEh:005Eh Other Memory
|__Device 01h
| |__Function 0 10DEh:0050h PCI to ISA Bridge
| |__Function 1 10DEh:0052h SMBus Controller Serial
|__Device 02h
| |__Function 0 10DEh:005Ah USB (OHCI) Serial
| |__Function 1 10DEh:005Bh USB 2.0 (EHCI) Serial
|__Device 06h 10DEh:0053h IDE (ATA) Storage
|__Device 07h 10DEh:0054h IDE (ATA) Storage
|__Device 09h 10DEh:005Ch PCI to PCI (Subtractive Decode) Bridge
Bus 1
Click to expand...
|__Device 0Ah 10DEh:0057h PCI to Other Bridge
|__Device 0Bh 10DEh:005Dh PCI to PCI Bridge > Bus 2
|__Device 0Ch 10DEh:005Dh PCI to PCI Bridge > Bus 3
|__Device 0Dh 10DEh:005Dh PCI to PCI Bridge > Bus 4
|__Device 0Eh 10DEh:005Dh PCI to PCI Bridge > Bus 5
|__Device 18h
|__Function 0 1022h:1100h PCI to HOST Bridge
|__Function 1 1022h:1101h PCI to HOST Bridge
|__Function 2 1022h:1102h PCI to HOST Bridge
|__Function 3 1022h:1103h PCI to HOST Bridge

--Bus 1 (PCI)
|__Device 07h 13F6h:0111h Audio Multimedia

--Bus 2
|__No Devices Currently Present

--Bus 3
|__No Devices Currently Present

--Bus 4 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

--Bus 5 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

A total of 20 Devices Found

I have been trying to install Vista for 3 days now. I realize that it is
BETA, but FFS, this is rediculous. I am by no means a computer expert, but I
know how to install an OS. IT should'nt be this much hassle and fuss.

Thanks for all your input, It is greatly appreciated.

Victor

**********************************************************
 
Hi all,

Just wanted to share my experiences with you, in hopes of finding a
resolution to this most annoying prblem...

I too get the BSOD after first reboot in Vista install. It seems that the
general concensus is that 7B is Vista not liking something on the IDE bus.
So, I unplugged the ONLY IDE drive from the mobo (Pioneer DVR-109), and
disabled all IDE channels in the BIOS. I then rebooted, and deleted all the
files that Vista had written to my XP partition (C: ), copied the Vista DVD
to the partition I want to install it on (D: ), and ran setup from the hard
drive, which by the way, is 2 WD 740 GD's in RAID 0 on Nvidia SATA ports 3
and 4. So there are NO IDE devices AT ALL.

And guess what? Still got the 7B stop error.

I tried booting in safe mode, to finish the install, I disabled driver sig
checking, enabled boot logging, none having the desired effect of allowing
Vista to finish installing.

I will attach pci32's report in its entirety, in hopes that someone will see
what I have been unable to see.

Report-Date = 23-06-2006 (D-M-Y)


PC-Model =


=== F u l l R e p o r t ================================================



Bus 0 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Eh nForce4 Memory Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Memory, type Other
New Capabilities List Present:
HyperTransport Capability
SubType : Slave/Primary Interface
Base UnitID : 0
UnitID Count : 15
HyperTransport Capability
SubType : MSI Mapping

Bus 0 (PCI Express), Device Number 1, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0050h nForce4 PCI to ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp

Bus 0 (PCI Express), Device Number 1, Device Function 1
Vendor 10DEh Nvidia Corp
Device 0052h nForce4 SMBus
Command 0001h (I/O Access)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type SMBus Controller
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 0000FC00h
Address 4 is an I/O Port : 00001C00h
Address 5 is an I/O Port : 00001C40h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ah nForce4 USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (OHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02F000h
System IRQ 22, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 1
Vendor 10DEh Nvidia Corp
Device 005Bh nForce4 USB 2.0 Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FEB00000h
System IRQ 20, INT# B
New Capabilities List Present:
USB 2.0 EHCI Debug Port Capability
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 6, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0053h nForce4 Parallel ATA Controller
Command 0005h (I/O Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 4 is an I/O Port : 0000F000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 7, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0054h nForce4 Serial ATA Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is in native mode at Addresses 0 & 1
Secondary Channel is in native mode at Addresses 2 & 3
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 000009F0h
Address 1 is an I/O Port : 00000BF0h
Address 2 is an I/O Port : 00000970h
Address 3 is an I/O Port : 00000B70h
Address 4 is an I/O Port : 0000DC00h
Address 5 is a Memory Address (anywhere in 0-4Gb) : FE02D000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 9, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ch nForce4 PCI Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A2h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 0204h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master
Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : None
Prefetchable Memory Range Passed to Secondary Bus : None

Bus 0 (PCI Express), Device Number 10, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0057h nForce4 Ethernet Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 01h, Maximum Bus Latency 14h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02C000h
Address 1 is an I/O Port : 0000D800h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 11, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 2
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000B000h to 0000BFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDD00000h to FDDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDC00000h to
00000000FDCFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Fatal Error Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : xReserved
Link Port Number : 3
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Link Training Error Reported!!
Slot Capabilities :
Slot Power Limit Value : 6.000 Watts
Physical slot Number 1

Bus 0 (PCI Express), Device Number 12, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus Number 3
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000A000h to 0000AFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDB00000h to FDBFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDA00000h to
00000000FDAFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x4
Link Port Number : 2
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Slot Capabilities :
Slot Power Limit Value : 4.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 13, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 4, Subordinate Bus Number 4
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00009000h to 00009FFFh (32-bit)
Memory Range Passed to Secondary Bus : FA000000h to FCFFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000D0000000h to
00000000DFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 2.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 14, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 5, Subordinate Bus Number 5
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00008000h to 00008FFFh (32-bit)
Memory Range Passed to Secondary Bus : F7000000h to F9FFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000C0000000h to
00000000CFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 0.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 24, Device Function 0
Vendor 1022h Advanced Micro Devices (AMD)
Device 1100h Athlon 64 / Opteron HyperTransport Technology Configuration
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
New Capabilities List Present:
HyperTransport Capability
SubType : Host/Secondary Interface

Bus 0 (PCI Express), Device Number 24, Device Function 1
Vendor 1022h Advanced Micro Devices (AMD)
Device 1101h Athlon 64 / Opteron Address Map
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 2
Vendor 1022h Advanced Micro Devices (AMD)
Device 1102h Athlon 64 / Opteron DRAM Controller
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 3
Vendor 1022h Advanced Micro Devices (AMD)
Device 1103h Athlon 64 / Opteron Miscellaneous Control
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 1 (PCI), Device Number 7, Device Function 0
Vendor 13F6h C-Media Electronics Inc
Device 0111h CMI8738/C3DX PCI Audio Device
Command 0085h (I/O Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 02h, Maximum Bus Latency 18h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 3741584Dh Unknown
Subsystem Vendor 584Dh Unknown
Address 0 is an I/O Port : 0000CC00h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 4 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : FA000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
D0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : FB000000h
Address 5 is an I/O Port : 00009C00h
System IRQ 19, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8

Bus 5 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0006h (Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
C0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : F8000000h
Address 5 is an I/O Port : 00008C80h
System IRQ 18, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8


IRQ Summary: IRQs 10,14,15,18,19,20,21,22,23 are used by PCI devices
Shared IRQs: IRQ 19 is shared by 2 PCI Devices

IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...


PCI Busses, Devices and Device Functions Tree

--Bus 0 (PCI Express)
|__Device 00h 10DEh:005Eh Other Memory
|__Device 01h
| |__Function 0 10DEh:0050h PCI to ISA Bridge
| |__Function 1 10DEh:0052h SMBus Controller Serial
|__Device 02h
| |__Function 0 10DEh:005Ah USB (OHCI) Serial
| |__Function 1 10DEh:005Bh USB 2.0 (EHCI) Serial
|__Device 06h 10DEh:0053h IDE (ATA) Storage
|__Device 07h 10DEh:0054h IDE (ATA) Storage
|__Device 09h 10DEh:005Ch PCI to PCI (Subtractive Decode) Bridge
Bus 1
Click to expand...
|__Device 0Ah 10DEh:0057h PCI to Other Bridge
|__Device 0Bh 10DEh:005Dh PCI to PCI Bridge > Bus 2
|__Device 0Ch 10DEh:005Dh PCI to PCI Bridge > Bus 3
|__Device 0Dh 10DEh:005Dh PCI to PCI Bridge > Bus 4
|__Device 0Eh 10DEh:005Dh PCI to PCI Bridge > Bus 5
|__Device 18h
|__Function 0 1022h:1100h PCI to HOST Bridge
|__Function 1 1022h:1101h PCI to HOST Bridge
|__Function 2 1022h:1102h PCI to HOST Bridge
|__Function 3 1022h:1103h PCI to HOST Bridge

--Bus 1 (PCI)
|__Device 07h 13F6h:0111h Audio Multimedia

--Bus 2
|__No Devices Currently Present

--Bus 3
|__No Devices Currently Present

--Bus 4 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

--Bus 5 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

A total of 20 Devices Found

I have been trying to install Vista for 3 days now. I realize that it is
BETA, but FFS, this is rediculous. I am by no means a computer expert, but I
know how to install an OS. IT should'nt be this much hassle and fuss.

Thanks for all your input, It is greatly appreciated.

Victor
 
Hi all,

Just wanted to share my experiences with you, in hopes of finding a
resolution to this most annoying prblem...

I too get the BSOD after first reboot in Vista install. It seems that the
general concensus is that 7B is Vista not liking something on the IDE bus.
So, I unplugged the ONLY IDE drive from the mobo (Pioneer DVR-109), and
disabled all IDE channels in the BIOS. I then rebooted, and deleted all the
files that Vista had written to my XP partition (C: ), copied the Vista DVD
to the partition I want to install it on (D: ), and ran setup from the hard
drive, which by the way, is 2 WD 740 GD's in RAID 0 on Nvidia SATA ports 3
and 4. So there are NO IDE devices AT ALL.

And guess what? Still got the 7B stop error.

I tried booting in safe mode, to finish the install, I disabled driver sig
checking, enabled boot logging, none having the desired effect of allowing
Vista to finish installing.

I will attach pci32's report in its entirety, in hopes that someone will see
what I have been unable to see.

Report-Date = 23-06-2006 (D-M-Y)


PC-Model =


=== F u l l R e p o r t ================================================



Bus 0 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Eh nForce4 Memory Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Memory, type Other
New Capabilities List Present:
HyperTransport Capability
SubType : Slave/Primary Interface
Base UnitID : 0
UnitID Count : 15
HyperTransport Capability
SubType : MSI Mapping

Bus 0 (PCI Express), Device Number 1, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0050h nForce4 PCI to ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp

Bus 0 (PCI Express), Device Number 1, Device Function 1
Vendor 10DEh Nvidia Corp
Device 0052h nForce4 SMBus
Command 0001h (I/O Access)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type SMBus Controller
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 0000FC00h
Address 4 is an I/O Port : 00001C00h
Address 5 is an I/O Port : 00001C40h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ah nForce4 USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (OHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02F000h
System IRQ 22, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 1
Vendor 10DEh Nvidia Corp
Device 005Bh nForce4 USB 2.0 Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FEB00000h
System IRQ 20, INT# B
New Capabilities List Present:
USB 2.0 EHCI Debug Port Capability
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 6, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0053h nForce4 Parallel ATA Controller
Command 0005h (I/O Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 4 is an I/O Port : 0000F000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 7, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0054h nForce4 Serial ATA Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is in native mode at Addresses 0 & 1
Secondary Channel is in native mode at Addresses 2 & 3
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 000009F0h
Address 1 is an I/O Port : 00000BF0h
Address 2 is an I/O Port : 00000970h
Address 3 is an I/O Port : 00000B70h
Address 4 is an I/O Port : 0000DC00h
Address 5 is a Memory Address (anywhere in 0-4Gb) : FE02D000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 9, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ch nForce4 PCI Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A2h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 0204h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master
Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : None
Prefetchable Memory Range Passed to Secondary Bus : None

Bus 0 (PCI Express), Device Number 10, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0057h nForce4 Ethernet Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 01h, Maximum Bus Latency 14h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02C000h
Address 1 is an I/O Port : 0000D800h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 11, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 2
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000B000h to 0000BFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDD00000h to FDDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDC00000h to
00000000FDCFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Fatal Error Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : xReserved
Link Port Number : 3
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Link Training Error Reported!!
Slot Capabilities :
Slot Power Limit Value : 6.000 Watts
Physical slot Number 1

Bus 0 (PCI Express), Device Number 12, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus Number 3
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000A000h to 0000AFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDB00000h to FDBFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDA00000h to
00000000FDAFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x4
Link Port Number : 2
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Slot Capabilities :
Slot Power Limit Value : 4.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 13, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 4, Subordinate Bus Number 4
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00009000h to 00009FFFh (32-bit)
Memory Range Passed to Secondary Bus : FA000000h to FCFFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000D0000000h to
00000000DFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 2.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 14, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 5, Subordinate Bus Number 5
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00008000h to 00008FFFh (32-bit)
Memory Range Passed to Secondary Bus : F7000000h to F9FFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000C0000000h to
00000000CFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 0.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 24, Device Function 0
Vendor 1022h Advanced Micro Devices (AMD)
Device 1100h Athlon 64 / Opteron HyperTransport Technology Configuration
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
New Capabilities List Present:
HyperTransport Capability
SubType : Host/Secondary Interface

Bus 0 (PCI Express), Device Number 24, Device Function 1
Vendor 1022h Advanced Micro Devices (AMD)
Device 1101h Athlon 64 / Opteron Address Map
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 2
Vendor 1022h Advanced Micro Devices (AMD)
Device 1102h Athlon 64 / Opteron DRAM Controller
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 3
Vendor 1022h Advanced Micro Devices (AMD)
Device 1103h Athlon 64 / Opteron Miscellaneous Control
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 1 (PCI), Device Number 7, Device Function 0
Vendor 13F6h C-Media Electronics Inc
Device 0111h CMI8738/C3DX PCI Audio Device
Command 0085h (I/O Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 02h, Maximum Bus Latency 18h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 3741584Dh Unknown
Subsystem Vendor 584Dh Unknown
Address 0 is an I/O Port : 0000CC00h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 4 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : FA000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
D0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : FB000000h
Address 5 is an I/O Port : 00009C00h
System IRQ 19, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8

Bus 5 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0006h (Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
C0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : F8000000h
Address 5 is an I/O Port : 00008C80h
System IRQ 18, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8


IRQ Summary: IRQs 10,14,15,18,19,20,21,22,23 are used by PCI devices
Shared IRQs: IRQ 19 is shared by 2 PCI Devices

IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...


PCI Busses, Devices and Device Functions Tree

--Bus 0 (PCI Express)
|__Device 00h 10DEh:005Eh Other Memory
|__Device 01h
| |__Function 0 10DEh:0050h PCI to ISA Bridge
| |__Function 1 10DEh:0052h SMBus Controller Serial
|__Device 02h
| |__Function 0 10DEh:005Ah USB (OHCI) Serial
| |__Function 1 10DEh:005Bh USB 2.0 (EHCI) Serial
|__Device 06h 10DEh:0053h IDE (ATA) Storage
|__Device 07h 10DEh:0054h IDE (ATA) Storage
|__Device 09h 10DEh:005Ch PCI to PCI (Subtractive Decode) Bridge
Bus 1
Click to expand...
|__Device 0Ah 10DEh:0057h PCI to Other Bridge
|__Device 0Bh 10DEh:005Dh PCI to PCI Bridge > Bus 2
|__Device 0Ch 10DEh:005Dh PCI to PCI Bridge > Bus 3
|__Device 0Dh 10DEh:005Dh PCI to PCI Bridge > Bus 4
|__Device 0Eh 10DEh:005Dh PCI to PCI Bridge > Bus 5
|__Device 18h
|__Function 0 1022h:1100h PCI to HOST Bridge
|__Function 1 1022h:1101h PCI to HOST Bridge
|__Function 2 1022h:1102h PCI to HOST Bridge
|__Function 3 1022h:1103h PCI to HOST Bridge

--Bus 1 (PCI)
|__Device 07h 13F6h:0111h Audio Multimedia

--Bus 2
|__No Devices Currently Present

--Bus 3
|__No Devices Currently Present

--Bus 4 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

--Bus 5 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

A total of 20 Devices Found

I have been trying to install Vista for 3 days now. I realize that it is
BETA, but FFS, this is rediculous. I am by no means a computer expert, but I
know how to install an OS. IT should'nt be this much hassle and fuss.

Thanks for all your input, It is greatly appreciated.

Victor
 
Errm, I dont know what happened with my post... it seems to be kinda buggy in
here too...

This forum isnt beta is it?
 
Sorry I wasn't quite clear. What I meant was that the 7b error does not care
what kind of cable or drive you use. I assumed the "IDE driver" was vague
enough to imply both PATA+SATA controllers.

Did you try the measures suggested in my first reply to this thread? How
about unplugging all the SATA drives and trying install on PATA drive? After
that I can only think of two: Get A PCI(e) controller for which you can find
a driver that has the txtsetup.oem or somesuch so the Vista setup can read
it before it starts to look for the drives.

I'd also try getting the boot log by enabling it from the boot menu before
the 7b comes. It could contain something useful, or not.
 
First of all, I want to apologize for the 4 posts that I seem to have
posted... i honestly don't know why it came up 4 times... maybe because I was
using Firefox? Again, I'm sorry. The first post is really long, and having 3
more certainly isn't much fun to scroll through...

As to your post droid, I was under the impression that SATA and IDE channels
are two separate things, as they are controlled by 2 different controllers in
XP.

Unfortunately, I do not have a PATA drive to install Vista onto.

I tried enabling boot logging again, and couldn't find ntbtlog.txt anywhere
on my machine after booting back to XP and searching the entire computer...

I have since my last post, udated the BIOS, and chipset drivers, as well the
RAID drivers. I have installed all recommended updates on my XP install (
thanks to Vista corrupting my XP install ) after a completely fresh install
of XP.

So at this point, I think I have had 0x0000007B at least 40 times. I really
want to see what this new OS can do, as my system should make it fly in all
it's glory... I'm running an FX-55, DFI NF4 SLI-DR, 2 x WD Raptors in RAID 0
on the nVidia controller, a Pioneer DVR-109, 2 x BFG 7800 GTX in SLI, 2Gb ( 4
x 512 ) OCZ PC3200 Plat. Rev. 2 and an HDA X-Plosion 7.1 DTS soundcard.

All drivers are as up to date as they can be... I really don't know what
else to do.

I guess I'll just have to w8 until the final build is released to the public.

Thanks agin for all your help, and if you think of anything else, please
post it.. I'll try anything at this point...

Cheers,


Victor
 
Well if "anything" goes then it may or may not help to get some cheap SATA
controller such as Si3112/4.. Got one of these from ebay at some $20-30.
Then get the driver from silicon image pages and see it has the
txtsetup.oem. Then just point the driver to the installer.

I haven't tried to install vista on my SI yet so I don't know if it works. I
only know the SI3112/4 work atleast when the driver is after OS has
installed.
 
Thanks droid.. was startin to think you had given up on me...lol

The DFI has the Sil 3114 built in, so perhaps I can use that? But I heard
that Sil haven't released a Vista compatible driver...

Thanks again,


H
 
Hey again, just sharing my continued problem installing Vista...

Well, it seems that Vista still doesn't like my system, evewn though I have
now tried to install 5456.

I get the same error after the first reboot.

The sad thing is that the Vista upgrade advisor has told me that my system
is Vista compatible.

Nvidia have released updated drivers, which I used, and the rest of my
system is compatible. It does not mention ANY IDE devices. None.

I tried all the previous suggetions, like disabling signature checks, enable
boot logging... etc etc... none works for me. The boot logging doesn't even
work. There is no ntbtlog.txt in the root of the installation drive, or any
drive for that matter.

Man I sure wish Linux was more of a gaming platform, cause I have had it
with MS. I realize this is BETA software, but ffs, my system is by no means
unique or out of the ordinary.
 
Well,

I get the same error in build 5456.

After Vista Upgrade Advisor told me that my system was compatible.

Nvidia have released updated drivers for vista, but still doesn't work.

5456 is supposed to have nvidia drivers integrated from what i have read.

Linux is starting to look pretty sweet right about now.

Is there some way to report this error to MS? Manually I mean, as I don't
get any log of whats happening. Just the 0x0000007b stop error BSOD.

I sure as hell am not going to pay $300-$500 for Vista when I can't even see
what it looks like. It'd be like buying a car without test driving it. Just
aint gonna happen...

Any other suggetions, aside from learning Linux? lol i would really
appreciate some help from some MS folks. It would go a long way towards
keeping me as a customer....
 
My brother had a problem VERY similar to this, if not exactly the same when
he tried to install Vista 64-bit on his machine, which happens to be an
NVIDIA based chipset. The sucker would just not boot after installation on a
RAID 0 SATA setup, it was like the SATA drivers were being erased from the
HDD while the install was rebooting. It made a mess of his WinXP
installation too, that wouldn't boot either, kept getting a 7b or NTLDIR is
missing!

My solution..... OK it may not be available to you all, but I went into my
brother's bios when he was out with friends, so he couldn't sit there
bitching and putting me off while I worked... in the advanced settings I
found a switch that allows you to choose the mode of the SATA disks
installed in your system... Though you need SATA disks to be set up as a
RAID 0 for the installation to work, once it comes to the point where it
won't boot into windows when it should, restart, go into bios, look for a
setting that lets you change from SATA mode to IDE mode, and it boots no
problem at all... did on my brother's machine anywho... hope this helps some
of y'all :-D
 
Back
Top