"Routing and Remote Access" in Windows Server 2003

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

Hi all....

I configured a Windows 2003 Server machine with "Routing and Remote Access"
but client computers cannot connect to Internet.

Ths is a simplified scenario:
..- Windows Server 2003 configured as Domain Controller, DNS, Active
Directory and DHCP Server. This server has 2 NIC's. One connects to a DSL
modem (let's say NIC A from now on) and the other to a hub (let's say NIC B
from now on).
..- One client computer with Windows 2000 Professional with 1 NIC connected
to the hub.

The configuration I set for each PC is as follows:

1) Server

- Name: WEBSERVER
- Windows 2003 Server, Standard Edition acting as DC, DNS, DHCP Server and
Active Directory
- Software Installed: Exchange server
- NIC A (that connects to the DSL modem) is assigned static IP 10.0.0.1,
automatic DNS and no gateway
- NIC B (that connects to the hub) is assigned static IP 192.168.1.1,
automatic DNS and no gateway.
- Internet connection correctly established. That network connection is set
to have automatic addressing, automatic DNS and no gateway. When I run
IPCONFIG, it shows that IP, gateway and DNS are assigned correctly by my ISP.
- I used the "Routing and Remote Access" wizard to configure the server. I
chose NAT radio button, and then I chose NIC A adapter
- In DNS console, I added my ISP DNS in the forwarder, so that when an
address is not resolved by this server, it will be redirected to my ISP DNS
servers

2) Client computer

- Name: CAROLINA
- Windows 2000 professional
- NIC connected to the hub and automatic IP addressing, automatic DNS and no
gateway.
- When I ping WEBSERVER, it delays some time to resolve the IP but it
finally resolves to the correct one: 192.168.1.1 and PING is successful.
- When I ping an Internet site, for example, www.google.cl, it cannot
resolve the name.

In conclusion, LAN works but it cannot connect to Internet through the server.

What may be wrong with this configuration?

Thanks a lot in advance
Jaime
 
make sure no filtering block the internet access. also check the NAT
settings if you enable it.

--
For more and other information, go to http://www.ChicagoTech.net

Don't send e-mail or reply to me except you need consulting services.
Posting on MS newsgroup will benefit all readers and you may get more help.

Bob Lin, MS-MVP, MCSE & CNE
Networking, Internet, Routing, VPN, Anti-Virus, Tips & Troubleshooting on
http://www.ChicagoTech.net
Networking Solutions, http://www.chicagotech.net/networksolutions.htm
VPN Solutions, http://www.chicagotech.net/vpnsolutions.htm
VPN Process and Error Analysis, http://www.chicagotech.net/VPN process.htm
VPN Troubleshooting, http://www.chicagotech.net/vpn.htm
This posting is provided "AS IS" with no warranties.
 
Hi Robert,

Can you please give me a more specific answer? is it clear that is a
configuration problem and that I have to enable IP routing or whatever. You
say that I have to make sure no filtering blocks internet address, but.. how
can I make sure of that? I have found several dialog boxes where I can
configure Inbound and Outbound filters (all different among themselves)

You also say that I have to check NAT settings if I configure it, but, there
are a lot of settings, so, what specific setting do I have to check?

Additionally I tell you that I have read a lot of documents on Internet,
specially technical white papers in Microsoft Web Site. I have done all the
documents say, I have followed all step-by-step instructions but I could
never make my LAN clients to connect to Internet through the Windows 2003
Server computer. That's why, as a last resource, I posted the question here.

I have told that I have 2 NIC's in the server, I assigned to the one that
connects to the DSL modem the static IP 10.0.0.1 and to the one that connects
to the LAN the IP 192.168.1.1. Is that correct? I can think that I have 2
different networks so the only problem I think I have to resolve is how to
make the LAN NIC to send the packets it receives from the LAN to the DSL NIC
so that it can send them to the DSL modem.

In "Routing and Remote Access" I have added both NICS. How can I configure
filters (or routing) in this case? Do I need to have a Routing Policy? the
wizard has added one by default (I used VPN and NAT option when the wizard
asked me), is this suficient?

One of the document I have read says that when I have configured a VPN
network, LAN clients computers can connect to other computers in the LAN or
to the Internet, but not to both. Is that true? When I run the wizard, the
VPN and NAT option label says that it is for connecting LAN client computers
to Internet, but after the wizard finished, the LAN work perfectly, but it
cannot connect to Internet.

Any further help will be greatly appreciated

Thanks
Jaime
 
Back
Top