Registry errors preventing WIN2K booting

  • Thread starter Thread starter Matthew
  • Start date Start date
M

Matthew

Dear All,

When my Win2K machine boots I get an error:

Stop: c0000218 {RegistryFile Failure}
The regristry cannot load the hive (file):
\SystemRoot\System32\Config\SOFTWARE
or its log or alternate.
It is corrupt, absent or not writable.

The machine then reboots and gets stuck in a loop. Is
there any way I can recover from this without having to do
a clean install?

TIA

Matthew
 
If the software hive is corrupt, it may be possible to rename the software
hive found in;
%windir%\system32\config\software
to software.old
then copy the most recent backup found in
%windir%\repair\regback
as
%windir%\system32\config\software

If that fails you can copy/ use the file
%windir%\repair\software
This file is an image of the hive at the time the OS was installed, so you'd
have to reinstall all software. This being the case you might just as well
blow it away and start a new install. (note: this would at least allow you
to start the OS to make any necessary backups prior to wiping the drive.)

To start the Recovery Console, start the computer from the Windows 2000
Setup CD or the Windows 2000 Setup floppy disks. If you do not have Setup
floppy disks and your computer cannot start from the Windows 2000 Setup CD,
use another Windows 2000-based computer to create the Setup floppy disks.
Press ENTER at the "Setup Notification" screen. Press R to repair a Windows
2000 installation, and then press C to use the Recovery Console. The
Recovery Console then prompts you for the administrator password. If you do
not have the correct password, Recovery Console does not allow access to the
computer. If an incorrect password is entered three times, the
RecoveryConsole quits and restarts the computer. Once the password has been
validated, you have full access to the Recovery Console, but limited access
to the hard disk. You can only access the following folders on your
computer: %systemroot% and %windir%

As a last resort;

Windows 2000 Registry Repair Utility
http://www.microsoft.com/downloads/...01-2C68-4DE8-9229-CA494362419C&displaylang=en
 
If the software hive is corrupt, it may be possible to rename the software
hive found in;
%windir%\system32\config\software
to software.old
then copy the most recent backup found in
%windir%\repair\regback
as
%windir%\system32\config\software

If that fails you can copy/ use the file
%windir%\repair\software
This file is an image of the hive at the time the OS was installed, so you'd
have to reinstall all software. This being the case you might just as well
blow it away and start a new install. (note: this would at least allow you
to start the OS to make any necessary backups prior to wiping the drive.)

To start the Recovery Console, start the computer from the Windows 2000
Setup CD or the Windows 2000 Setup floppy disks. If you do not have Setup
floppy disks and your computer cannot start from the Windows 2000 Setup CD,
use another Windows 2000-based computer to create the Setup floppy disks.
Press ENTER at the "Setup Notification" screen. Press R to repair a Windows
2000 installation, and then press C to use the Recovery Console. The
Recovery Console then prompts you for the administrator password. If you do
not have the correct password, Recovery Console does not allow access to the
computer. If an incorrect password is entered three times, the
RecoveryConsole quits and restarts the computer. Once the password has been
validated, you have full access to the Recovery Console, but limited access
to the hard disk. You can only access the following folders on your
computer: %systemroot% and %windir%

As a last resort;

Windows 2000 Registry Repair Utility
http://www.microsoft.com/downloads/...01-2C68-4DE8-9229-CA494362419C&displaylang=en
 
Back
Top