p3b-f and tualatin celeron cpu, cpu temp question?

  • Thread starter Thread starter Donald White
  • Start date Start date
D

Donald White

Group,

I read so much here about people sticking a Tualatin CPU in their p2bs
and p3bs that I had to go and try it myself in my p3b-f. I used a 1.3
GHz cpu and a slot-t since both were relatively cheap. Everything works
fine, but then I am not overclocking. I do notice that asusprobe
reports that this cpu is about 10 degrees C warmer than my p3-750MHz,
mid 40s versus mid 30s. Is this normal or do I have a cooling problem.
The cpu is a retail version with stock fan. Under heavy load encoding
a DVD, the temp rises to 51C or so.

Thanks,

Don
 
Donald White said:
Group,

I read so much here about people sticking a Tualatin CPU in their p2bs
and p3bs that I had to go and try it myself in my p3b-f. I used a 1.3
GHz cpu and a slot-t since both were relatively cheap. Everything works
fine, but then I am not overclocking. I do notice that asusprobe
reports that this cpu is about 10 degrees C warmer than my p3-750MHz,
mid 40s versus mid 30s. Is this normal or do I have a cooling problem.
The cpu is a retail version with stock fan. Under heavy load encoding
a DVD, the temp rises to 51C or so.

Thanks,

Don
Click to expand...

You could check the Vcore being fed to the processor. Look up the
five character code called the SSPEC on the processor, at this site:

http://processorfinder.intel.com

Compare the Vcore listed, to the Vcore shown in the BIOS Power
Monitor page. (Probably in the neighbourhood of 1.5V.)

A processor can run hot if it runs faster than normal (overclock),
you are using a higher Vcore than normal, or the cooling solution
isn't making good contact.

Also, check the "motherboard temperature". If the air in the
case is hotter than normal, the CPU cooling solution won't work
as well as if the case air was cooler. So, really, it is the
delta_T and not the absolute temp, that tells you how good the
cooling is working.

HTH,
Paul
 
Donald said:
Group,

I read so much here about people sticking a Tualatin CPU in their p2bs
and p3bs that I had to go and try it myself in my p3b-f. I used a 1.3
GHz cpu and a slot-t since both were relatively cheap. Everything works
fine, but then I am not overclocking. I do notice that asusprobe
reports that this cpu is about 10 degrees C warmer than my p3-750MHz,
mid 40s versus mid 30s. Is this normal or do I have a cooling problem.
The cpu is a retail version with stock fan. Under heavy load encoding
a DVD, the temp rises to 51C or so.
Click to expand...

These seem perfectly normal temps for a 1.3 GHz Tualatin. You also have
to keep in mind that this processor not only has a higher maximum power
dissipation (TDP is 33.4 W instead of 19.5 W) but also exhibits
considerable leakage currents that drive idle power consumption to
almost 15 W. (The Tualatin was Intel's first 0.13µ processor, and it
shows.)

Stephan
 
Paul said:
You could check the Vcore being fed to the processor. Look up the
five character code called the SSPEC on the processor, at this site:

http://processorfinder.intel.com

Compare the Vcore listed, to the Vcore shown in the BIOS Power
Monitor page. (Probably in the neighbourhood of 1.5V.)
Click to expand...

Vcore is slightly under 1.5, 1.472-1.49, as reported by BIOS, cpuid and
asusprobe. This is true regardless of the BIOS Vcore setting. I get a
Vcore warning on boot if I do not set the BIOS monitor to ignore Vcore
voltage errors. This seems to be normal for this MB/CPU combination.
A processor can run hot if it runs faster than normal (overclock),
you are using a higher Vcore than normal, or the cooling solution
isn't making good contact.
Click to expand...

No overclocking here.
Also, check the "motherboard temperature". If the air in the
case is hotter than normal, the CPU cooling solution won't work
as well as if the case air was cooler. So, really, it is the
delta_T and not the absolute temp, that tells you how good the
cooling is working.
Click to expand...

MB temp is 32C which is 3-4 degrees above room temp. Case has extra
inlet and outlet fans, plus HD fans.
 
Stephan said:
These seem perfectly normal temps for a 1.3 GHz Tualatin. You also have
to keep in mind that this processor not only has a higher maximum power
dissipation (TDP is 33.4 W instead of 19.5 W) but also exhibits
considerable leakage currents that drive idle power consumption to
almost 15 W. (The Tualatin was Intel's first 0.13µ processor, and it
shows.)

Stephan
Click to expand...

Thanks, I didn't realize the cpu TDP increased so much. I will watch my
case temperatures to see if more cooling is needed there.

Don
 
Back
Top