S
seree
I currently have two XP Media Center desktops behind a Belkin router. Each
system has both wired and wireless adapters, both are now enabled. I am
unable to establish a network connection with the wired adapters, but finally
got the (old setup) Wireless adapters to communicate and transfer data
between the machines. I want to disconnect and remove the Wireless adapters,
and keep the Wired adapters. I can't seem to establish any network
connectivity with the Wired adapters, and can't remove the Wireless until I
do. Frustrating! ;-)
Without giving too much information, I will attempt to sketch the situation.
Connection Type: Dynamic
Subnet Mask : 255.255.255.0
Routers IP : 192.168.2.1
Modems IP : 192.168.0.2
ISP Default Gateway : 192.168.0.1
DNS addresses : 192.168.0.1. and 205.171.3.65
All information was entered into the Belkin router automatically during its
"Quick Installation" mode, using the software CD.
As of the router setup, both Belkin Pre-N wireless adapters could access
both the internet and the internal network. An issue came up with an
unexpected reduction in network status speed. It was suppose to be 300Mbps,
the Pre-N had been 108Mbps, but this N1 was reporting the G speed of 54Mbps.
I phoned Belkin technical support.
A short history. Both systems came with pre-installed Intel 10/100 wired
adapters. Due to distance issue, I had to use wireless. I have since moved,
and can now utilize the wired adapters, and meant to when I had time to set
it up. Then the Pre-N router burnt out and Belkin replaced it with the
'upgrade" N1.
Short story, after "troubleshooting" the network speed issue with Belkin
technician, I was advised to "upgrade" the software on each Pre-N adapter, to
'coincide' with the new N1 router. Huh? lol
Anyway, I set a manual restore point and proceeded to do just that in one
system, the other was waiting with the download package on the desktop. After
the installation and a reboot, I was unable to acquire an IP address for that
adapter. When I attempted to do a System Restore that system experienced a
fatal error and I had to do a Repair of the OS.
So, I did so, and once the OS was "repaired" I went ahead and hooked it up
with a cable to the router. I had already done so with the other system as it
has a faster theoretical network speed and browsed faster. I disabled each
Wireless adapter in the Network Connection folder. Each system has a reliable
internet connection without any of the intermittent disconnections I use to
receive on the Wireless adapter. (My major issue and reason for wanting to go
wired)
After setting the Repaired system up, recreating the proper accounts on both
systems for a Workgroup network, all the same accounts/passwords, (I deleted
my 'old' account on the unbroken computer because I changed the User Name of
the account on the Repaired system, and it needed to match for networking
purposes, as I always change the Access this Computer from the Network
setting, from the Everyone group to Authenticated Users group, in Local
Security Settings)
I then attempted to access data I had stored on my second system, yet when I
opened my Network Places in the Repaired computer, nothing was listed there.
I used the Run box to attempt to connect via the path, and received an error
stating the Server did not exist or I did not have permissions and to check
with the Administrator. lol
I then checked connectivity, pinged the Modem, the Router, and well known
websites. All has solid connectivity. I then attempted to ping what I thought
were each IP address for each computer. Nothing.
I then used ipconfig /all to find out the IP addresses. Much to my surprise
they were not only high on the list of avaiable IP addresses, but not in
ordere. I use WPA encryption and MAC address lists to allow only the
computers listed to connect to the router.
I then went into my routers configuration pages to check on the IP addresses
assigned.
Repaired computer has two: 192.168.2.4 and 192.168.2.5
Other computer has two : 192.168.2.3 and 192.168.2.7
My address range is: 192.168.2.2 to 192.168.2.100
Finally, I have something to work with, but am extremely puzzled. Why are
these IP addresses assigned as they are above? I thought a DHCP Server
assigns in a series starting at the lowest, and up until the last system is
assigned, not this oddly sequenced addressing.
I have a firewall activated in the router. Encryption is WPA and locked
tightly. I had used a MAC address Allow list to control which computers could
hook up to the network, regardless of Wired or Wireless. Cool feature by the
way.
Also, I finally took one further step: I enabled the Wireless adapters. My
network is now working in those adapters, but nothing on the Wired adapters,
not even a ping. I am able to freely see and access my resources on both
system as long as I keep the Wireless adapters enabled. As soon as I disable
them, network connectivity is finished. I want to remove these adapters from
the computers completely. I don't need two adapters in desktops any longer.
Not in this location anyway. lol
Sorry this is so long. I really tried keeping it short. I hope it isn't too
confusing, that I outlined it clearly enough. I understand what I mean to
say, but I hope you experts follow my distorted network situation. I already
rewrote this three times and am going to send it as it is now. I do apologize
most sincerely if I over described or didn't explain it in correct order or
format.
Thank you to anyone who wishes to respond and assist me in straightening out
whatever I have done wrong. Any further correspondence shouldn't be so long.
system has both wired and wireless adapters, both are now enabled. I am
unable to establish a network connection with the wired adapters, but finally
got the (old setup) Wireless adapters to communicate and transfer data
between the machines. I want to disconnect and remove the Wireless adapters,
and keep the Wired adapters. I can't seem to establish any network
connectivity with the Wired adapters, and can't remove the Wireless until I
do. Frustrating! ;-)
Without giving too much information, I will attempt to sketch the situation.
Connection Type: Dynamic
Subnet Mask : 255.255.255.0
Routers IP : 192.168.2.1
Modems IP : 192.168.0.2
ISP Default Gateway : 192.168.0.1
DNS addresses : 192.168.0.1. and 205.171.3.65
All information was entered into the Belkin router automatically during its
"Quick Installation" mode, using the software CD.
As of the router setup, both Belkin Pre-N wireless adapters could access
both the internet and the internal network. An issue came up with an
unexpected reduction in network status speed. It was suppose to be 300Mbps,
the Pre-N had been 108Mbps, but this N1 was reporting the G speed of 54Mbps.
I phoned Belkin technical support.
A short history. Both systems came with pre-installed Intel 10/100 wired
adapters. Due to distance issue, I had to use wireless. I have since moved,
and can now utilize the wired adapters, and meant to when I had time to set
it up. Then the Pre-N router burnt out and Belkin replaced it with the
'upgrade" N1.
Short story, after "troubleshooting" the network speed issue with Belkin
technician, I was advised to "upgrade" the software on each Pre-N adapter, to
'coincide' with the new N1 router. Huh? lol
Anyway, I set a manual restore point and proceeded to do just that in one
system, the other was waiting with the download package on the desktop. After
the installation and a reboot, I was unable to acquire an IP address for that
adapter. When I attempted to do a System Restore that system experienced a
fatal error and I had to do a Repair of the OS.
So, I did so, and once the OS was "repaired" I went ahead and hooked it up
with a cable to the router. I had already done so with the other system as it
has a faster theoretical network speed and browsed faster. I disabled each
Wireless adapter in the Network Connection folder. Each system has a reliable
internet connection without any of the intermittent disconnections I use to
receive on the Wireless adapter. (My major issue and reason for wanting to go
wired)
After setting the Repaired system up, recreating the proper accounts on both
systems for a Workgroup network, all the same accounts/passwords, (I deleted
my 'old' account on the unbroken computer because I changed the User Name of
the account on the Repaired system, and it needed to match for networking
purposes, as I always change the Access this Computer from the Network
setting, from the Everyone group to Authenticated Users group, in Local
Security Settings)
I then attempted to access data I had stored on my second system, yet when I
opened my Network Places in the Repaired computer, nothing was listed there.
I used the Run box to attempt to connect via the path, and received an error
stating the Server did not exist or I did not have permissions and to check
with the Administrator. lol
I then checked connectivity, pinged the Modem, the Router, and well known
websites. All has solid connectivity. I then attempted to ping what I thought
were each IP address for each computer. Nothing.
I then used ipconfig /all to find out the IP addresses. Much to my surprise
they were not only high on the list of avaiable IP addresses, but not in
ordere. I use WPA encryption and MAC address lists to allow only the
computers listed to connect to the router.
I then went into my routers configuration pages to check on the IP addresses
assigned.
Repaired computer has two: 192.168.2.4 and 192.168.2.5
Other computer has two : 192.168.2.3 and 192.168.2.7
My address range is: 192.168.2.2 to 192.168.2.100
Finally, I have something to work with, but am extremely puzzled. Why are
these IP addresses assigned as they are above? I thought a DHCP Server
assigns in a series starting at the lowest, and up until the last system is
assigned, not this oddly sequenced addressing.
I have a firewall activated in the router. Encryption is WPA and locked
tightly. I had used a MAC address Allow list to control which computers could
hook up to the network, regardless of Wired or Wireless. Cool feature by the
way.
Also, I finally took one further step: I enabled the Wireless adapters. My
network is now working in those adapters, but nothing on the Wired adapters,
not even a ping. I am able to freely see and access my resources on both
system as long as I keep the Wireless adapters enabled. As soon as I disable
them, network connectivity is finished. I want to remove these adapters from
the computers completely. I don't need two adapters in desktops any longer.
Not in this location anyway. lol
Sorry this is so long. I really tried keeping it short. I hope it isn't too
confusing, that I outlined it clearly enough. I understand what I mean to
say, but I hope you experts follow my distorted network situation. I already
rewrote this three times and am going to send it as it is now. I do apologize
most sincerely if I over described or didn't explain it in correct order or
format.
Thank you to anyone who wishes to respond and assist me in straightening out
whatever I have done wrong. Any further correspondence shouldn't be so long.