NIC Config Gots Lost

  • Thread starter Thread starter Ashish Bagla
  • Start date Start date
A

Ashish Bagla

When I disable & enable my lan card it works fine for 30 secs & immi after
that it losts its ip address & other confis...

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8139(A) PCI Fast
Ethernet
Adapter #3
Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . :
----------------------------------------------------------------------------
---------
Immi after 30 secs or so... it shows...

Ethernet adapter Local Area Connection:

Media State . . . . . . . . . . . : Cable Disconnected
Description . . . . . . . . . . . : Realtek RTL8139(A) PCI Fast
Ethernet
Adapter #3
Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
 
Event log says the following

Description:
The system detected that network adapter Realtek RTL8139(A) PCI Fast
Ethernet Adapter #3 was disconnected from the network, and the adapter's
network configuration has been released. If the network adapter was not
disconnected, this may indicate that it has malfunctioned. Please contact
your vendor for updated drivers.
 
Event Log also says
" The Routing and Remote Access service depends on the NetBIOSGroup group and no member of this group started. "

" SAM failed to start the TCP/IP or SPX/IPX listening thread "

Event Source: NetBT
Initialization failed because the transport refused to open initial Addresses.
 
P.S. : When I try to enable teh NIC it gets enabled for couple of seconds & during that time it is pingable but immi after that it beocmes non pingable & says connection failed in the NIC enabling box.


Event Log also says
" The Routing and Remote Access service depends on the NetBIOSGroup group and no member of this group started. "

" SAM failed to start the TCP/IP or SPX/IPX listening thread "

Event Source: NetBT
Initialization failed because the transport refused to open initial Addresses.
 
Have you tried a new network card, new cable, or different jack on your
networking device?

--
Richard G. Harper [MVP Win9x] (e-mail address removed)
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


P.S. : When I try to enable teh NIC it gets enabled for couple of seconds &
during that time it is pingable but immi after that it beocmes non pingable
& says connection failed in the NIC enabling box.


Event Log also says
" The Routing and Remote Access service depends on the NetBIOSGroup group
and no member of this group started. "

" SAM failed to start the TCP/IP or SPX/IPX listening thread "

Event Source: NetBT
Initialization failed because the transport refused to open initial
Addresses.
 
I have tried 2 different NIC's in2 diff slots.

Even if the canble is un plugged & the cards ip address is 192.168.0.1 it
will respond to self ping.

If responds for approx 30 secs after the card is activated & then the error
comes saying connection failed...

Ashish

Richard G. Harper said:
Have you tried a new network card, new cable, or different jack on your
networking device?

--
Richard G. Harper [MVP Win9x] (e-mail address removed)
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


P.S. : When I try to enable teh NIC it gets enabled for couple of seconds &
during that time it is pingable but immi after that it beocmes non pingable
& says connection failed in the NIC enabling box.


Event Log also says
" The Routing and Remote Access service depends on the NetBIOSGroup group
and no member of this group started. "

" SAM failed to start the TCP/IP or SPX/IPX listening thread "

Event Source: NetBT
Initialization failed because the transport refused to open initial
Addresses.



Ashish Bagla said:
Event log says the following

Description:
The system detected that network adapter Realtek RTL8139(A) PCI Fast
Ethernet Adapter #3 was disconnected from the network, and the adapter's
network configuration has been released. If the network adapter was not
disconnected, this may indicate that it has malfunctioned. Please contact
your vendor for updated drivers.
Click to expand...
Click to expand...
 
How is the computer connected to the network? Switch, router, or ???

Have you checked for spyware, adware or viruses?

--
Richard G. Harper [MVP Win9x] (e-mail address removed)
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


Ashish Bagla said:
I have tried 2 different NIC's in2 diff slots.

Even if the canble is un plugged & the cards ip address is 192.168.0.1 it
will respond to self ping.

If responds for approx 30 secs after the card is activated & then the
error
comes saying connection failed...

Ashish

Richard G. Harper said:
Have you tried a new network card, new cable, or different jack on your
networking device?

--
Richard G. Harper [MVP Win9x] (e-mail address removed)
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


P.S. : When I try to enable teh NIC it gets enabled for couple of seconds &
during that time it is pingable but immi after that it beocmes non pingable
& says connection failed in the NIC enabling box.


Event Log also says
" The Routing and Remote Access service depends on the NetBIOSGroup group
and no member of this group started. "

" SAM failed to start the TCP/IP or SPX/IPX listening thread "

Event Source: NetBT
Initialization failed because the transport refused to open initial
Addresses.



Ashish Bagla said:
Event log says the following

Description:
The system detected that network adapter Realtek RTL8139(A) PCI Fast
Ethernet Adapter #3 was disconnected from the network, and the adapter's
network configuration has been released. If the network adapter was not
disconnected, this may indicate that it has malfunctioned. Please contact
your vendor for updated drivers.

When I disable & enable my lan card it works fine for 30 secs & immi
after
that it losts its ip address & other confis...

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8139(A) PCI Fast
Ethernet
Adapter #3
Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . :
Click to expand...
--------------------------------------------------------------------------
--
---------
Immi after 30 secs or so... it shows...

Ethernet adapter Local Area Connection:

Media State . . . . . . . . . . . : Cable Disconnected
Description . . . . . . . . . . . : Realtek RTL8139(A) PCI Fast
Ethernet
Adapter #3
Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
Click to expand...
Click to expand...
Click to expand...
 
yes

Nothing is there

Ashish


Richard G. Harper said:
How is the computer connected to the network? Switch, router, or ???

Have you checked for spyware, adware or viruses?

--
Richard G. Harper [MVP Win9x] (e-mail address removed)
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


Ashish Bagla said:
I have tried 2 different NIC's in2 diff slots.

Even if the canble is un plugged & the cards ip address is 192.168.0.1 it
will respond to self ping.

If responds for approx 30 secs after the card is activated & then the
error
comes saying connection failed...

Ashish

Richard G. Harper said:
Have you tried a new network card, new cable, or different jack on your
networking device?

--
Richard G. Harper [MVP Win9x] (e-mail address removed)
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


P.S. : When I try to enable teh NIC it gets enabled for couple of
Click to expand...
seconds
&
during that time it is pingable but immi after that it beocmes non pingable
& says connection failed in the NIC enabling box.


Event Log also says
" The Routing and Remote Access service depends on the NetBIOSGroup group
and no member of this group started. "

" SAM failed to start the TCP/IP or SPX/IPX listening thread "

Event Source: NetBT
Initialization failed because the transport refused to open initial
Addresses.



Event log says the following

Description:
The system detected that network adapter Realtek RTL8139(A) PCI Fast
Ethernet Adapter #3 was disconnected from the network, and the adapter's
network configuration has been released. If the network adapter was not
disconnected, this may indicate that it has malfunctioned. Please
contact
your vendor for updated drivers.

When I disable & enable my lan card it works fine for 30 secs &
immi
after
that it losts its ip address & other confis...

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8139(A) PCI
Fast
Ethernet
Adapter #3
Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . :
Click to expand...

------------------------------------------------------------------------- -
--
---------
Immi after 30 secs or so... it shows...

Ethernet adapter Local Area Connection:

Media State . . . . . . . . . . . : Cable Disconnected
Description . . . . . . . . . . . : Realtek RTL8139(A) PCI
Fast
Ethernet
Adapter #3
Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
Click to expand...
Click to expand...
Click to expand...
 
Back
Top