Need a TWAIN_32.DLL version 1.8 or higher

  • Thread starter Thread starter Steve Zodiac
  • Start date Start date
S

Steve Zodiac

Hi all,

I have a problem in programming the TWAIN interface and the toolkit
supplier says I need to upgrade TWAIN_32.DLL to version 1.8 as later.

Please can someone point me to a location for this file.

TIA
Steve
 
Out of curiosity I followed that link because it seemed unlikely that they'd
have a compiled version, and I also could not find it, only the developers'
tools. Hoever, I did a search on my computer (WindozeXP) and found version
1.6.0.1 in C:\windows\system32 and version 1.7.1.0 in C:\windows. I haven't
checked to see which one is being used, but you might try the same thing,
and if you find the later version, copy it over the top of the old one.

You might also try a search on the M$ site. They're more likely to have
it, I think.

Don
 
Steve Zodiac said:
Hi all,

I have a problem in programming the TWAIN interface and the toolkit
supplier says I need to upgrade TWAIN_32.DLL to version 1.8 as later.

Please can someone point me to a location for this file.

TIA
Steve
Click to expand...

You don't say what scanner or program requires this driver

Try this site
http://www.scanner-drivers.com/

Gus
 
You don't say what scanner or program requires this driver

Try this site
http://www.scanner-drivers.com/

Gus
Click to expand...
My assumption was that this file was hardware independent - maybe I'm
wrong (I think it did happen once before :-), but I'm trying to drive
a Kodak i260 and access it's capabilities via the TWAIN interface, it
has been suggested that a version of the TWAIN_32.DLL that is 1.8 or
greater will help. But can I find it?
 
Steve Zodiac said:
My assumption was that this file was hardware independent - maybe I'm
wrong (I think it did happen once before :-), but I'm trying to drive
a Kodak i260 and access it's capabilities via the TWAIN interface, it
has been suggested that a version of the TWAIN_32.DLL that is 1.8 or
greater will help. But can I find it?
Click to expand...

I found the following on the kodak website


http://www.kodak.com/global/mul/bus...XWJA?id=8200294&cc=US&lc=en&_requestid=151835

i200 Series Scanner Validation Tool

Latest i200 Series Scanner Validation Tool and Brightness Contrast
Control

Installing the latest Scanner Validation Tool (SVT) from the link on the
bottom of this page will install both the latest TWAIN Data Source, and
the latest ISIS Driver for the i200 Series Scanners. You must install
the SVT to access these drivers, and to use the integrated Host Image
Processing software, known as HIPPO.

All i200 Series Scanners, with or without the Flatbed Accessory, should
be brought up to this level of Host Software, and the Firmware MUST be
updated to v 2.01.01 i200 Firmware after the new SVT is installed. If
this isn't done the scanner will not work properly.

Software Driver Versions included in the latest SVT - February 2004

a.. TWAIN data source V4.7.16.2 (This is a 32-bit data source, and is
TWAIN 1.9 compliant)

b.. ISIS driver 1.1.10312.23001

c.. HIPPO v2.5.0 (Host Image Processing for both TWAIN and ISIS
Drivers)

d.. STI driver v 1.0.1.0

Gus
 
Steve Zodiac said:
Maybe I'm being thicker than usual, but that I spent some time looking
through the twain site and couldn't find that particular file. Am I
missing it somehow?
Click to expand...

I misunderstood what you were wanting. I took your original post indicated
you were programming a
TWAIN interface for some hardware and needed the 1.8 and later strings.
 
Back
Top