My X2 5400 is running too hot

  • Thread starter Thread starter Mac Cool
  • Start date Start date
M

Mac Cool

I upgraded my machine from a Sempron 3000 to an X2 5400 and it's running
too hot, about 55c average, jumps to 62-65 under load. I'm using the stock
heat sink/fan but I still don't think it should get that hot. I have no
case fans.

According to Speedfan my temps under load are:
temp1: 64
temp2: 46
temp3: 25
hd0: 47
hd1: 48
temp1: 30
core: 66

Rosewill case
ECS 6100 MB

What is my best bet? A fan for the side of the case?
 
I upgraded my machine from a Sempron 3000 to an X2 5400 and it's running
too hot, about 55c average, jumps to 62-65 under load. I'm using the
stock heat sink/fan but I still don't think it should get that hot. I
have no case fans.

According to Speedfan my temps under load are: temp1: 64
temp2: 46
temp3: 25
hd0: 47
hd1: 48
temp1: 30
core: 66

Rosewill case
ECS 6100 MB

What is my best bet? A fan for the side of the case?
Click to expand...

Your case temp2 is way too high if it's accurate. CPU being only 18C above
that during load isn't bad. You could duct the cpu fan to the side panel,
or install a front intake fan. Either should help.
 
Wes Newell:
Your case temp2 is way too high if it's accurate. CPU being only 18C
above that during load isn't bad. You could duct the cpu fan to the
side panel, or install a front intake fan. Either should help.
Click to expand...

When you say duct tape to the side, do you mean create a tunnel so the CPU
fan is drawing outside air over the processer? That sounds like a good
idea.

Tomorrow I'll open it up and see about fitting a front intake fan.
 
Wes Newell:


When you say duct tape to the side, do you mean create a tunnel so the
CPU fan is drawing outside air over the processer? That sounds like a
good idea.
Click to expand...
Actually, I meant cutting a round hole in the cover in line with the cpu
cooler and ducting the outside air to the cooler fan using an air duct.
But this may be too much of an extreme measure. Just cutting the hole
about 3" in dia. should help a lot.
Tomorrow I'll open it up and see about fitting a front intake fan.
Click to expand...

I've had to modify every case I ever installed a front intake fan in.
Otherwise the fan just starves for outside air and is real noisy. Maybe
before doing anything you should remove the side cover and see what that
does to temps. Then you'll have something to go on.
 
R. C. White:
Hmmm... I don't see the word "tape" in Wes's post. :^}
Click to expand...

Oh man, reading is fundamental. At least I got what he meant even if I
didn't read what he wrote.
 
Wes Newell:
Actually, I meant cutting a round hole in the cover in line with the cpu
cooler and ducting the outside air to the cooler fan using an air duct.
But this may be too much of an extreme measure. Just cutting the hole
about 3" in dia. should help a lot.
Click to expand...

I actually have a hole alread there and another square vent hole several
inches below that. Putting a duct in is a good idea.
I've had to modify every case I ever installed a front intake fan in.
Otherwise the fan just starves for outside air and is real noisy. Maybe
before doing anything you should remove the side cover and see what that
does to temps. Then you'll have something to go on.
Click to expand...

I went ahead and peeked in there and it doesn't seem there is hardly any
ventilation in the front. I would definitely have to cut something
otherwise a fan would be sucking plastic.

I took the side cover off and directed a fan into the case.

first number is with case side on under load, second number is case side
off under load.

temp1: 64 50
temp2: 46 40
temp3: 25 25
hd0: 47 36
hd1: 48 37
core: 66 54

Much better.
 
I took the side cover off and directed a fan into the case.

first number is with case side on under load, second number is case side
off under load.

temp1: 64 50
temp2: 46 40
temp3: 25 25
hd0: 47 36
hd1: 48 37
core: 66 54

Much better.
Click to expand...

Yep. And your HDD's will last a lot longer too with cooler temps.
 
Back
Top