K8V Deluxe SATA (no RAID)

  • Thread starter Thread starter Boff
  • Start date Start date
B

Boff

I've just purchased a K8V Deluxe and Athlon 64 3000+ processor. I also
purchased a single 160GB SATA HD which I intend to use as my primary boot
drive. I have no interest in a RAID configuration at this time. Will any
of the 4 SATA connectors on this mobo (2 VIA and 2 Promise) be able to be
used as the primary boot connection or do I need to connect the drive to a
particular SATA connector? As I understand it, SATA drivers need to be
installed in order to use the SATA interfaces. If so, how do I do a format
of the new HD prior to installing the SATA drivers provided with the mobo?

Thank You in advance for any replies,

Boff
 
Boff said:
I've just purchased a K8V Deluxe and Athlon 64 3000+ processor. I also
purchased a single 160GB SATA HD which I intend to use as my primary boot
drive. I have no interest in a RAID configuration at this time. Will any
of the 4 SATA connectors on this mobo (2 VIA and 2 Promise) be able to be
used as the primary boot connection or do I need to connect the drive to a
particular SATA connector? As I understand it, SATA drivers need to be
installed in order to use the SATA interfaces. If so, how do I do a format
of the new HD prior to installing the SATA drivers provided with the mobo?

Thank You in advance for any replies,

Boff
Click to expand...

For a single drive, connect it to the connector labeled SATA1 next to the
VIA southbridge. This is the primary connector on the VIA southbridge and
should provide the best throughput. It is where mine is connected. You
will need to make a driver floppy from the files on the CD that came with
the board if you want to install your OS directly to the SATA drive. You
don't say which OS you are going to install, but if it is Windows 2000/XP,
boot off the install cd and press F6 when prompted. Follow the directions
to install the third party drivers. After loading this driver, you will be
able to format and install as usual. I didn't get my SATA drive until after
I had all the other parts, so I installed on a standard IDE drive, installed
the drivers once in XP/2000 and then ghosted my IDE drive to my SATA drive
when it arrived. After ghosting, since the drivers were already on the
drive, I could boot in the same manner as if I had installed XP/2000 on the
SATA drive to begin with.

Sick Willie
 
Sick Willie said:
news:[email protected]...
Click to expand...
the drivers once in XP/2000 and then ghosted my IDE drive to my SATA drive
when it arrived. After ghosting, since the drivers were already on the
drive, I could boot in the same manner as if I had installed XP/2000 on the
SATA drive to begin with.

Sick Willie
Click to expand...

Sorry to digress here, I'm planning on switching to SATA at somepoint, and
wondered could I get away with copying the partition (Partition Magic) after
installing SATA drivers from IDE to SATA drive, or would I have to do the
repair install trick to get XP to recognise the different HDD Controller?

Cheers
 
Dave said:
Sorry to digress here, I'm planning on switching to SATA at somepoint, and
wondered could I get away with copying the partition (Partition Magic) after
installing SATA drivers from IDE to SATA drive, or would I have to do the
repair install trick to get XP to recognise the different HDD Controller?

Cheers
Click to expand...
No repair install should be needed if all your doing is switching from
PATA to SATA. Just install the Drivers on the IDE disk before Ghosting
to the SATA. Change BIOS to boot off the SATA and away you go. I did
this with 3 drives, so I'm sure it will work.

Rob
 
Dave Catchpole said:
Sorry to digress here, I'm planning on switching to SATA at somepoint, and
wondered could I get away with copying the partition (Partition Magic) after
installing SATA drivers from IDE to SATA drive, or would I have to do the
repair install trick to get XP to recognise the different HDD Controller?

Cheers
Click to expand...

As long as Partition Magic does as complete a job as Ghost does, you will
have no problem. If you attempted the repair install, you would have to
supply the drivers on floppy since XP would not find them on the CD as thus
would not find your SATA hard drive.

Sick Willie
 
Sick Willie said:
For a single drive, connect it to the connector labeled SATA1 next to the
VIA southbridge. This is the primary connector on the VIA southbridge and
should provide the best throughput. It is where mine is connected. You
will need to make a driver floppy from the files on the CD that came with
the board if you want to install your OS directly to the SATA drive. You
don't say which OS you are going to install, but if it is Windows 2000/XP,
boot off the install cd and press F6 when prompted. Follow the directions
to install the third party drivers. After loading this driver, you will be
able to format and install as usual. I didn't get my SATA drive until after
I had all the other parts, so I installed on a standard IDE drive, installed
the drivers once in XP/2000 and then ghosted my IDE drive to my SATA drive
when it arrived. After ghosting, since the drivers were already on the
drive, I could boot in the same manner as if I had installed XP/2000 on the
SATA drive to begin with.

Sick Willie
Click to expand...

Thanks for the reply. I will be installing Win XP Pro on the drive. I'll
follow your instructions and see how it goes.

Thanks Again,

Boff
 
As long as Partition Magic does as complete a job as Ghost does, you will
have no problem. If you attempted the repair install, you would have to
supply the drivers on floppy since XP would not find them on the CD as thus
would not find your SATA hard drive.

Sick Willie
Click to expand...

Ghost was the other option that I was thinking of.

Note, the SATA interface is not onboard, on an external PCI card, will that
still be usable as a boot device, would it be treated as a SCSI card in the
bios similar to how XP shows the controller in the Device manager?

Regards and many thanks so far!

Dave
 
Dave Catchpole said:
Ghost was the other option that I was thinking of.

Note, the SATA interface is not onboard, on an external PCI card, will that
still be usable as a boot device, would it be treated as a SCSI card in the
bios similar to how XP shows the controller in the Device manager?

Regards and many thanks so far!

Dave
Click to expand...

You would treat it as SCSI in setup, and as long as it has a boot BIOS
(which I am sure it does) you will be good to go.

Sick Willie
 
Back
Top