(K8V Deluxe) How do you keep the CPU fan spinning??

  • Thread starter Thread starter Quality Mime Supplies
  • Start date Start date
Q

Quality Mime Supplies

I have the K8V Deluxe motherboard with a Zalman cooler fan installed
instead of the stock fan from AMD.

This combination appears to work well although I did not install the
Zalman's fan regulator. It was suggested that I let the Motheboard do
the work.

The cpu temp varies between 41 and 52 degrees and the Probe utility
most always shows the CPU fan to be off (visual inspection supports this).

I guess I'm OK with this but I really would prefer the fan to be ON.
However, I can't seem to get the right settings to do this. I have played
with the BIOS settings but nothing seems to work.

Suggestions? I'm a little reluctant to upgrade my BIOS to see if there
is a fix. When it comes to BIOS, I adopt a 'if it ain't broke....'
attitude.
 
I have the K8V Deluxe motherboard with a Zalman cooler fan installed
instead of the stock fan from AMD.

This combination appears to work well although I did not install the
Zalman's fan regulator. It was suggested that I let the Motheboard do
the work.

The cpu temp varies between 41 and 52 degrees and the Probe utility
most always shows the CPU fan to be off (visual inspection supports this).

I guess I'm OK with this but I really would prefer the fan to be ON.
However, I can't seem to get the right settings to do this. I have played
with the BIOS settings but nothing seems to work.

Suggestions? I'm a little reluctant to upgrade my BIOS to see if there
is a fix. When it comes to BIOS, I adopt a 'if it ain't broke....'
attitude.
Click to expand...

Strange ! Asus Probe should not monitor the fan.
Speedfan can do it.

The zalman fan regulator is just a down adjustment.

What happens if you connect the fan to another fan stick on the
motherboard. Which one should not matter. They all carry 12 volt.

I use a zalman 7000 on my abit NF7 and it spins 2650 rpm all the time.
This make my cpu 35 C by ordinary, almost idle, work.

I have it below 50C by full load.

best regards

John
 
JK said:
Strange ! Asus Probe should not monitor the fan.
Speedfan can do it.

The zalman fan regulator is just a down adjustment.

What happens if you connect the fan to another fan stick on the
motherboard. Which one should not matter. They all carry 12 volt.
Click to expand...
Not true, lots of boards won't even start unless they detect a fan on the
CPU fan header.

SteveH
 
The cpu temp varies between 41 and 52 degrees and the Probe utility
most always shows the CPU fan to be off (visual inspection supports this).

I guess I'm OK with this but I really would prefer the fan to be ON.
However, I can't seem to get the right settings to do this. I have played
with the BIOS settings but nothing seems to work.
Click to expand...


In BIOS (Power - Hardware Monitor) set Q-Fan Control to "Disabled".

Siegfried
 
"Siegfried Zech" said:
In BIOS (Power - Hardware Monitor) set Q-Fan Control to "Disabled".

Siegfried
Click to expand...

http://www.asus.com/mb/qfan.htm

On older Q-fan implementations, there was a "ratio" setting, and
I think that set the relationship between minimum speed and maximum
speed. Like, a setting of 11/15, meant at temperatures below 50C,
the fan would get a voltage of 12V*(11/15).

On the K8V, there is no ratio setting.

It could be, that Asus decided the combination of "Cool and Quiet"
gives such a low heat output of the CPU, that they could let the
ratio drop a lot lower, leading to the fan stopping. As you can see,
if the processor only gets to 42C, that isn't warm enough to trigger
Q-fan into running the fan. At 52C, Q-fan should be running the fan,
and that is why the temperature doesn't climb above that - in a
sense, the fan is being used to regulate the CPU temperature to 50C.

It is too bad the trigger points are not programmable, as reshaping
the curve would give you the response you want. Disabling Q-fan is
one solution to the problem. I think you'll find the minimum
temperature falls substantially.

Disabling Q-fan really depends on whether you find the noise of a
changing fan speed annoying or not.

Paul
 
(e-mail address removed) (Paul) wrote in
http://www.asus.com/mb/qfan.htm

On older Q-fan implementations, there was a "ratio" setting, and
I think that set the relationship between minimum speed and maximum
speed. Like, a setting of 11/15, meant at temperatures below 50C,
the fan would get a voltage of 12V*(11/15).

On the K8V, there is no ratio setting.

It could be, that Asus decided the combination of "Cool and Quiet"
gives such a low heat output of the CPU, that they could let the
ratio drop a lot lower, leading to the fan stopping. As you can see,
if the processor only gets to 42C, that isn't warm enough to trigger
Q-fan into running the fan. At 52C, Q-fan should be running the fan,
and that is why the temperature doesn't climb above that - in a
sense, the fan is being used to regulate the CPU temperature to 50C.

It is too bad the trigger points are not programmable, as reshaping
the curve would give you the response you want. Disabling Q-fan is
one solution to the problem. I think you'll find the minimum
temperature falls substantially.

Disabling Q-fan really depends on whether you find the noise of a
changing fan speed annoying or not.

Paul
Click to expand...

I currently use an Antec Sonata case which is very quiet. The Zalman
fan is also very quiet. I really don't notice either when it's under
the desk.
 
Back
Top