G
Guest
How can I run regedt.exe from recovery console. I have to
narrow the reg Hive because of sytem.ced problems
thanks
Guus
narrow the reg Hive because of sytem.ced problems
thanks
Guus
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
D
Dave Patrick
You can't.
If the system hive, and assuming you already tried LKG, It may be possible
to rename the system hive found in
%windir%\system32\config\system
to system.old
then rename
%windir%\system32\config\system.alt
to
%windir%\system32\config\system
You can also try using the most recent backup found in
%windir%\repair\regback
If that fails you haven't much choice but to copy/ use the
original-as-installed system hive from
%windir%\repair\system
to
%windir%\system32\config\system
You'll need to reinstall the device drivers for any hardware added since the
original OS install.
To start the Recovery Console, start the computer from the Windows 2000
Setup CD or the Windows 2000 Setup floppy disks. If you do not have Setup
floppy disks and your computer cannot start from the Windows 2000 Setup CD,
use another Windows 2000-based computer to create the Setup floppy disks.
Press ENTER at the "Setup Notification" screen. Press R to repair a Windows
2000 installation, and then press C to use the Recovery Console. The
Recovery Console then prompts you for the administrator password. If you do
not have the correct password, Recovery Console does not allow access to the
computer. If an incorrect password is entered three times, the Recovery
Console quits and restarts the computer. Once the password has been
validated, you have full access to the Recovery Console, but limited access
to the hard disk. You can only access the following folders on your
computer: %systemroot% and %windir%
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft MVP [Windows NT/2000 Operating Systems]
| How can I run regedt.exe from recovery console. I have to
| narrow the reg Hive because of sytem.ced problems
|
| thanks
|
| Guus
If the system hive, and assuming you already tried LKG, It may be possible
to rename the system hive found in
%windir%\system32\config\system
to system.old
then rename
%windir%\system32\config\system.alt
to
%windir%\system32\config\system
You can also try using the most recent backup found in
%windir%\repair\regback
If that fails you haven't much choice but to copy/ use the
original-as-installed system hive from
%windir%\repair\system
to
%windir%\system32\config\system
You'll need to reinstall the device drivers for any hardware added since the
original OS install.
To start the Recovery Console, start the computer from the Windows 2000
Setup CD or the Windows 2000 Setup floppy disks. If you do not have Setup
floppy disks and your computer cannot start from the Windows 2000 Setup CD,
use another Windows 2000-based computer to create the Setup floppy disks.
Press ENTER at the "Setup Notification" screen. Press R to repair a Windows
2000 installation, and then press C to use the Recovery Console. The
Recovery Console then prompts you for the administrator password. If you do
not have the correct password, Recovery Console does not allow access to the
computer. If an incorrect password is entered three times, the Recovery
Console quits and restarts the computer. Once the password has been
validated, you have full access to the Recovery Console, but limited access
to the hard disk. You can only access the following folders on your
computer: %systemroot% and %windir%
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft MVP [Windows NT/2000 Operating Systems]
| How can I run regedt.exe from recovery console. I have to
| narrow the reg Hive because of sytem.ced problems
|
| thanks
|
| Guus
D
Dave Patrick
You can't.
If the system hive, and assuming you already tried LKG, It may be possible
to rename the system hive found in
%windir%\system32\config\system
to system.old
then rename
%windir%\system32\config\system.alt
to
%windir%\system32\config\system
You can also try using the most recent backup found in
%windir%\repair\regback
If that fails you haven't much choice but to copy/ use the
original-as-installed system hive from
%windir%\repair\system
to
%windir%\system32\config\system
You'll need to reinstall the device drivers for any hardware added since the
original OS install.
To start the Recovery Console, start the computer from the Windows 2000
Setup CD or the Windows 2000 Setup floppy disks. If you do not have Setup
floppy disks and your computer cannot start from the Windows 2000 Setup CD,
use another Windows 2000-based computer to create the Setup floppy disks.
Press ENTER at the "Setup Notification" screen. Press R to repair a Windows
2000 installation, and then press C to use the Recovery Console. The
Recovery Console then prompts you for the administrator password. If you do
not have the correct password, Recovery Console does not allow access to the
computer. If an incorrect password is entered three times, the Recovery
Console quits and restarts the computer. Once the password has been
validated, you have full access to the Recovery Console, but limited access
to the hard disk. You can only access the following folders on your
computer: %systemroot% and %windir%
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft MVP [Windows NT/2000 Operating Systems]
| How can I run regedt.exe from recovery console. I have to
| narrow the reg Hive because of sytem.ced problems
|
| thanks
|
| Guus
If the system hive, and assuming you already tried LKG, It may be possible
to rename the system hive found in
%windir%\system32\config\system
to system.old
then rename
%windir%\system32\config\system.alt
to
%windir%\system32\config\system
You can also try using the most recent backup found in
%windir%\repair\regback
If that fails you haven't much choice but to copy/ use the
original-as-installed system hive from
%windir%\repair\system
to
%windir%\system32\config\system
You'll need to reinstall the device drivers for any hardware added since the
original OS install.
To start the Recovery Console, start the computer from the Windows 2000
Setup CD or the Windows 2000 Setup floppy disks. If you do not have Setup
floppy disks and your computer cannot start from the Windows 2000 Setup CD,
use another Windows 2000-based computer to create the Setup floppy disks.
Press ENTER at the "Setup Notification" screen. Press R to repair a Windows
2000 installation, and then press C to use the Recovery Console. The
Recovery Console then prompts you for the administrator password. If you do
not have the correct password, Recovery Console does not allow access to the
computer. If an incorrect password is entered three times, the Recovery
Console quits and restarts the computer. Once the password has been
validated, you have full access to the Recovery Console, but limited access
to the hard disk. You can only access the following folders on your
computer: %systemroot% and %windir%
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft MVP [Windows NT/2000 Operating Systems]
| How can I run regedt.exe from recovery console. I have to
| narrow the reg Hive because of sytem.ced problems
|
| thanks
|
| Guus