How can I re-allow default display adapter?

  • Thread starter Thread starter perky87
  • Start date Start date
P

perky87

Hi,

I have been very stupid. I am trying to get my NVIDIA card working in my
pc. However the card will not install properly and so it is using the
default adapter. I thought I had solved it and consequently disabled the
default adapter...

After the requested restart, windows is running but the monitor is blank
(power is on). So what I have done is to disallow the adapter...and I need
to re-allow it. This would be simple enough to do however its impossible to
do if you cannot see what you are doing! Any suggestions?!

I've tried going through the procedure on another machine and noting down
the shortcuts.. but this has not worked.. There must be an easier way?
 
Hi,

I have been very stupid.  I am trying to get my NVIDIA card working in my
pc.  However the card will not install properly and so it is using the
default adapter.  I thought I had solved it and consequently disabled the
default adapter...

After the requested restart, windows is running but the monitor is blank
(power is on).  So what I have done is to disallow the adapter...and I need
to re-allow it.  This would be simple enough to do however its impossible to
do if you cannot see what you are doing!  Any suggestions?!

I've tried going through the procedure on another machine and noting down
the shortcuts.. but this has not worked.. There must be an easier way?
Click to expand...

Start in Safe Mode and re-enable the default driver??
 
Hi,

I have been very stupid. I am trying to get my NVIDIA card working in my
pc. However the card will not install properly and so it is using the
default adapter. I thought I had solved it and consequently disabled the
default adapter...

After the requested restart, windows is running but the monitor is blank
(power is on). So what I have done is to disallow the adapter...and I need
to re-allow it. This would be simple enough to do however its impossible
to
do if you cannot see what you are doing! Any suggestions?!

I've tried going through the procedure on another machine and noting down
the shortcuts.. but this has not worked.. There must be an easier way?
Click to expand...

Start in Safe Mode and re-enable the default driver??

If he disabled the onboard adapter in the bios (which I suspect) he won't be
able to get into safe mode...

To the OP: If you disabled the onboard video in the bios you need to get
out the manual for the computer (or go online to the manufacturer's web
site) to find out how to reset the bios on the computer using the jumper on
the computer's motherboard. Once you figure out how to reset the bios do so
and the onboard video should start to work again.

Let us know if this is the issue and if this information helps or further
help is needed. If further help is needed you need to post at the minimum
the make and full model information of the computer.
 
LVTravel said:
Start in Safe Mode and re-enable the default driver??

If he disabled the onboard adapter in the bios (which I suspect) he won't be
able to get into safe mode...

To the OP: If you disabled the onboard video in the bios you need to get
out the manual for the computer (or go online to the manufacturer's web
site) to find out how to reset the bios on the computer using the jumper on
the computer's motherboard. Once you figure out how to reset the bios do so
and the onboard video should start to work again.

Let us know if this is the issue and if this information helps or further
help is needed. If further help is needed you need to post at the minimum
the make and full model information of the computer.
Click to expand...

Before using the Clear CMOS jumper, unplug the computer from the wall.

That is to handle those motherboards, where using the CMOS jumper with
+5VSB present, causes a small dual diode on the motherboard, to burn.
At least read the manual, to see if there is a warning about it.
(There are a few manuals, that actually have wrong instructions.
Caveat emptor.)

Paul
 
Start in Safe Mode and re-enable the default driver??

If he disabled the onboard adapter in the bios (which I suspect) he won'tbe
able to get into safe mode...

To the OP:  If you disabled the onboard video in the bios you need to get
out the manual for the computer (or go online to the manufacturer's web
site) to find out how to reset the bios on the computer using the jumper on
the computer's motherboard.  Once you figure out how to reset the bios do so
and the onboard video should start to work again.

Let us know if this is the issue and if this information helps or further
help is needed.  If further help is needed you need to post at the minimum
the make and full model information of the computer.
Click to expand...

The OP stated that they had disable the default adapter. I have done
this inside Windows Device Manager once and no display ever was
possible until I re-activated it.
 
Paul said:
Before using the Clear CMOS jumper, unplug the computer from the wall.

That is to handle those motherboards, where using the CMOS jumper with
+5VSB present, causes a small dual diode on the motherboard, to burn.
At least read the manual, to see if there is a warning about it.
(There are a few manuals, that actually have wrong instructions.
Caveat emptor.)

Paul
Click to expand...

I agree totally and that is why I posted "find out how to reset the bios."
Hopefully the manual will have the proper instructions. Manuals that I have
read for this all stated to turn off the computer, change the jumper,
restart the system, turn off, unplug and remove jumper.....etc. Never had
an issue from old PIII to present day systems resetting the bios, but I
always follow manufacturer's specifications.
 
Start in Safe Mode and re-enable the default driver??

If he disabled the onboard adapter in the bios (which I suspect) he won't
be
able to get into safe mode...

To the OP: If you disabled the onboard video in the bios you need to get
out the manual for the computer (or go online to the manufacturer's web
site) to find out how to reset the bios on the computer using the jumper
on
the computer's motherboard. Once you figure out how to reset the bios do
so
and the onboard video should start to work again.

Let us know if this is the issue and if this information helps or further
help is needed. If further help is needed you need to post at the minimum
the make and full model information of the computer.
Click to expand...

The OP stated that they had disable the default adapter. I have done
this inside Windows Device Manager once and no display ever was
possible until I re-activated it.

Agree, and some time the only way to re-enable from within Windows is to
total reinstall Windows as a repair install doesn't always fix it.
Hopefully it was a bios reset fix.
 
Back
Top