K
Ken Krone
Thanks for reading this...
I had an installation of Win2000 which had been running flawlessly on my
P4PE until this AM. My IDE 120GB hdd was plugged into the Primary IDE
socket.
I received a new 120GB SATA hard drive that I had purchased for
mirroring in RAID1. I moved my primary 120GB hdd to the RAID controller
on the PRI_RAID socket of the mb, enabled the Promise RAID controller
function, choose "Onboard ATA device first" yes and tried to boot,
which it did not. The boot sequence showed that the bios for the RAID
did not load, so I entered the Fasttrack and defined an array as a
striped drive for my only 120GB hdd. I exited and tried booting, which
did not work. Figuring that I could work that out later, I then shut
down, installed the second 120GB hdd and chose up a RAID1 array. The
mirroring process of the original drive with the new drive went well and
I rebooted with the RAID controller enabled in BIOS on my motherboard
and it did not work. I decided to go back to square one, so I disabled
the RAID and hooked up my original hdd the way it had been on the same
primary IDE connector, and tried to boot. The boot only goes as far as
finding the PCI assignments, then stops at a flashing cursor instead of
going on to load the Win2K operating system.
I set the Win2K CD-Rom as the boot device, booted the Win2000 CD-Rom and
selected the Repair option. The first option was to repair with the
console, which basically gave me a boot into what appears and functions
like DOS. I DIR'd my way through the various logical partitions and all
of my data is there. I TYPE'd the boot.ini file and it has the standard
command of multit(0)disk(0)rdisk(0)partition(1):\WINNT etc.
I then ran through the boot with the Win2K again and chose the option
that allows the operating system to repair itself. It ran through it
paces but when that was finished, I removed the CD-Rom, rebooted, and I
could still not boot into Win2K. The boot sequence stopped at the
flashing cursor after the PCI devices were listed.
So I am baffled as to how to get this disk, which is loaded with data
and Win2K, to boot. I would not mind doing an install if someone can
tell me which operating system files to back up on a different partition
so that I could regain all of my settings and registered programs but I
must be missing something simple in the boot sequence that needs to be
repaired. The other question is what on earth happened during the
attempt to set up the RAID that caused the problem in the first place.
I have checked my BIOS settings but they do not appear to have changed.
Many thanks in advance,
Ken K
Feel free to email me at the above corrected address...
I had an installation of Win2000 which had been running flawlessly on my
P4PE until this AM. My IDE 120GB hdd was plugged into the Primary IDE
socket.
I received a new 120GB SATA hard drive that I had purchased for
mirroring in RAID1. I moved my primary 120GB hdd to the RAID controller
on the PRI_RAID socket of the mb, enabled the Promise RAID controller
function, choose "Onboard ATA device first" yes and tried to boot,
which it did not. The boot sequence showed that the bios for the RAID
did not load, so I entered the Fasttrack and defined an array as a
striped drive for my only 120GB hdd. I exited and tried booting, which
did not work. Figuring that I could work that out later, I then shut
down, installed the second 120GB hdd and chose up a RAID1 array. The
mirroring process of the original drive with the new drive went well and
I rebooted with the RAID controller enabled in BIOS on my motherboard
and it did not work. I decided to go back to square one, so I disabled
the RAID and hooked up my original hdd the way it had been on the same
primary IDE connector, and tried to boot. The boot only goes as far as
finding the PCI assignments, then stops at a flashing cursor instead of
going on to load the Win2K operating system.
I set the Win2K CD-Rom as the boot device, booted the Win2000 CD-Rom and
selected the Repair option. The first option was to repair with the
console, which basically gave me a boot into what appears and functions
like DOS. I DIR'd my way through the various logical partitions and all
of my data is there. I TYPE'd the boot.ini file and it has the standard
command of multit(0)disk(0)rdisk(0)partition(1):\WINNT etc.
I then ran through the boot with the Win2K again and chose the option
that allows the operating system to repair itself. It ran through it
paces but when that was finished, I removed the CD-Rom, rebooted, and I
could still not boot into Win2K. The boot sequence stopped at the
flashing cursor after the PCI devices were listed.
So I am baffled as to how to get this disk, which is loaded with data
and Win2K, to boot. I would not mind doing an install if someone can
tell me which operating system files to back up on a different partition
so that I could regain all of my settings and registered programs but I
must be missing something simple in the boot sequence that needs to be
repaired. The other question is what on earth happened during the
attempt to set up the RAID that caused the problem in the first place.
I have checked my BIOS settings but they do not appear to have changed.
Many thanks in advance,
Ken K
Feel free to email me at the above corrected address...