Does this look right?

  • Thread starter Thread starter A64 Owner
  • Start date Start date
A

A64 Owner

I'm wondering why my ram is not reporting "2x 200MHz"
but is instead reporting:
Speed : 2x 167MHz (334MHz data rate)

?



SiSoftware Sandra

Mainboard
Manufacturer : Gigabyte Technology Co., Ltd.
MP Support : 1 CPU(s)
MPS Version : 1.40
Model : K8T800-8237
Version : 1.x
System BIOS : 08/03/2004-K8T800-8237-6A7L0G04C-00
Chipset : VIA K8HTB

System Memory Controller
Location : Mainboard
Error Correction Capability : None
Number of Memory Slots : 3
Maximum Installable Memory : 768MB
Bank0/1 - A0 : DIMM 1GB/64 @ 400Mt/s
Bank2/3 - A1 : DIMM 1GB/64 @ 400Mt/s
Bank4/5 - A2 : Empty

Chipset 1
Model : VIA Technologies Inc Apollo K8T800 CPU to PCI Bridge
Bus(es) : ISA AGP PCI IMB USB i2c/SMBus
Version : 1.02
Front Side Bus Speed : 2x 804MHz (1608MHz data rate)
In/Out Width : 16-bit / 16-bit
IO Queue Depth : 3 request(s)

Chipset 1 Hub Interface
Type : V-Link
In/Out Width : 4-bit / 4-bit
Multiplier : 1/1x
IO Queue Depth : 9 request(s)

Logical/Chipset 1 Memory Banks
Power Save Mode : No
Fixed Hole Present : No

Chipset 2
Model : Advanced Micro Devices (AMD) Athlon 64 / Opteron HyperTransport
Technology Configuration
Bus(es) : ISA AGP PCI IMB USB i2c/SMBus
Version : 1.02
Front Side Bus Speed : 2x 804MHz (1608MHz data rate)
Maximum FSB Speed / Max Memory Speed : 2x 1000MHz / 2x 200MHz
In/Out Width : 16-bit / 16-bit
IO Queue Depth : 8 request(s)

Chipset 2 Hub Interface
Type : HyperTransport
Version : 1.02
In/Out Width : 16-bit / 16-bit
Speed : 2x 804MHz (1608MHz data rate)

Logical/Chipset 2 Memory Banks
Bank 0 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Bank 1 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Bank 2 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Bank 3 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Channels : 1
Speed : 2x 167MHz (334MHz data rate)
Multiplier : 1/12x
Width : 64-bit
Refresh Rate : 6.00µs
Power Save Mode : No
Fixed Hole Present : No

APIC 1
Version : 0.03
Multiplier : 1/2x
Maximum Interrupts : 24
IRQ Handler Engaged : Yes
Enhanced Support : Yes

Memory Module 1
Type : 1GB DDR-SDRAM
Technology : 16x(64Mx8)
Speed : PC3200U 2.0-3-2-5
Date of Manufacture : Saturday, December 25, 1999
Set Timing @ 200MHz : 2.0-3-2-5

Memory Module 2
Type : 1GB DDR-SDRAM
Technology : 16x(64Mx8)
Speed : PC3200U 2.0-3-2-5
Date of Manufacture : Saturday, December 25, 1999
Set Timing @ 200MHz : 2.0-3-2-5

Environment Monitor 1
Model : ITE IT8705/12 ISA
Mainboard Specific Support : No

Temperature Sensor(s)
Board Temperature : 25.0°C / 77.0°F
CPU Temperature : 41.0°C / 105.8°F

Cooling Device(s)
Auto Fan Speed Control : No
Chassis Fan Speed : 3245rpm

Voltage Sensor(s)
CPU Voltage : 1.47V
Aux Voltage : 2.54V
+3.3V Voltage : 3.23V
+5V Voltage : 3.33V
+12V Voltage : 11.79V
-12V Voltage : -4.38V
-5V Voltage : -4.00V
Standby Voltage : 4.65V

AGP Bus(es) on Hub 1
Version : 3.00
Speed : 8x
Fast-Writes Enabled : No
Isochronous Mode Enabled : No
Addressing Enabled : 32-bit
Aperture Size : 128MB

PCI Bus(es) on Hub 1
Version : 2.10
Number of Bridges : 1
PCI Bus 0 : PCI (1/1x PCIClk)

LPC Hub Controller 1
Model : Giga-Byte Technology VT8237 PCI to ISA Bridge
ACPI Power Management Enabled : Yes
Multiplier : 1/4x
DMA Multiplier : 1/2x

USB Controller 1
Model : Giga-Byte Technology VT82xxxxx UHCI USB 1.1 Controller (All VIA
Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 2
Model : Giga-Byte Technology VT82xxxxx UHCI USB 1.1 Controller (All VIA
Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 3
Model : Giga-Byte Technology VT82xxxxx UHCI USB 1.1 Controller (All VIA
Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 4
Model : Giga-Byte Technology VT82xxxxx UHCI USB 1.1 Controller (All VIA
Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 5
Model : Giga-Byte Technology VT6202 USB 2.0 Enhanced Host Controller
Version : 2.00
Specification : 1.00
Interface : EHCI
Channels : 8
Companion Controllers : 4
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
Addressing Support : 32-bit
Legacy Emulation Enabled : No

System SMBus Controller 1
Model : VIA VT823x SMBus
Advanced TCO Mode Enabled : No
Slave Device Enabled : No
PEC Support : No
Speed : 16kHz

Expansion Slot(s)
PCI (9h) : PCI 32-bit +5V +3.3V PME Full-Length Available
PCI (Ah) : PCI 32-bit +5V +3.3V PME Full-Length Used (Voyetra
Technologies Crystal CS4630 SoundFusion PCI Audio Accelerator)
PCI (Bh) : PCI 32-bit +5V +3.3V PME Full-Length Used (Intel Corporation
PRO/1000 MT Desktop Adapter)
PCI (Ch) : PCI 32-bit +5V +3.3V PME Full-Length Available
PCI (Dh) : PCI 32-bit +5V +3.3V PME Full-Length Used (Hauppauge Computer
Works Inc WinTV PVR 250)
AGP (8h) : AGP 32-bit +5V Full-Length Used (PowerColor (C.P. Technology
Co Ltd) Radeon 9600 Series (V350))

Port Connector
PRIMARY IDE : None - ATA / None
SECONDARY IDE : None - ATA / None
FDD : 8251 FIFO - Floppy Disk / None
COM1 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
COM2 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
LPT1 : Parallel Port ECP/EPP - DB-25 pin female / DB-25 pin female
Keyboard : Keyboard - None / PS/2
PS/2 Mouse - Detected : Mouse - PS/2 / PS/2
USB : USB - None / USB

Performance Tips
Notice 224 : SMBIOS/DMI information may be inaccurate.
Tip 2511 : Some memory slots are free so the memory can be easily
upgraded.
Warning 100 : Large memory sizes should be made of Registered/Buffered
memory.
Tip 2546 : Large memory modules should be ECC/Parity.
Tip 2 : Double-click tip or press Enter while a tip is selected for more
information about the tip.




SiSoftware Sandra

Benchmark Results
RAM Bandwidth Int Buff'd iSSE2 : 2543 MB/s
RAM Bandwidth Float Buff'd iSSE2 : 2549 MB/s
Results Interpretation : Higher index values are better.

Int Buff'd iSSE2 (Integer STREAM) Results Breakdown
Assignment : 2550MB/s
Scaling : 2545MB/s
Addition : 2541MB/s
Triad : 2536MB/s
Data Item Size : 16 byte(s)
Buffering Used : Yes
Offset Displacement Used : Yes
Bandwidth Efficiency : 95% (estimated)

Float Buff'd iSSE2 (Float STREAM) Results Breakdown
Assignment : 2558MB/s
Scaling : 2552MB/s
Addition : 2545MB/s
Triad : 2543MB/s
Data Item Size : 16 byte(s)
Buffering Used : Yes
Offset Displacement Used : Yes
Bandwidth Efficiency : 95% (estimated)

Performance Test Status
Run ID : AMD64 on Wednesday, December 31, 2003 at 11:06:45 PM
Memory Used by Test : 512MB
NUMA Support : No
SMP Test : No
Total Test Threads : 1
Multi-Core Test : No
SMT Test : No
Dynamic MP/MT Load Balance : No
Processor Affinity : PP0
Page Size : 4kB
Use Large Memory Pages : No

Chipset 1
Model : VIA Technologies Inc Apollo K8T800 CPU to PCI Bridge
Front Side Bus Speed : 2x 804MHz (1608MHz data rate)
In/Out Width : 16-bit / 16-bit
Maximum Bus Bandwidth : 6432MB/s (estimated)

Logical/Chipset 1 Memory Banks

Chipset 2
Model : Advanced Micro Devices (AMD) Athlon 64 / Opteron HyperTransport
Technology Configuration
Front Side Bus Speed : 2x 804MHz (1608MHz data rate)
In/Out Width : 16-bit / 16-bit
Maximum Bus Bandwidth : 6432MB/s (estimated)

Logical/Chipset 2 Memory Banks
Bank 0 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Bank 1 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Bank 2 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Bank 3 : 512MB DDR-SDRAM 2.0-3-2-2 1CMD
Channels : 1
Speed : 2x 167MHz (334MHz data rate)
Width : 64-bit
Maximum Memory Bus Bandwidth : 2672MB/s (estimated)

Features
(W)MMX Technology : Yes
SSE Technology : Yes
SSE2 Technology : Yes
SSE3 Technology : No
EMMX - Extended MMX Technology : Yes
HTT - Hyper-Threading Technology : No

Performance Tips
Notice 5008 : To change benchmarks, click Options.
Notice 5004 : Synthetic benchmark. May not tally with 'real-life'
performance.
Notice 5006 : Only compare the results with ones obtained using the same
version!
Tip 233 : Consider using the Win64 x64 version of SiSoftware Sandra.
Tip 2 : Double-click tip or press Enter while a tip is selected for more
information about the tip.
 
I'm wondering why my ram is not reporting "2x 200MHz"
but is instead reporting:
Speed : 2x 167MHz (334MHz data rate)
Click to expand...
Probably because it's running at 167Mhz. You've either set it to that
speed or you have it set for BySPD.
 
Probably because it's running at 167Mhz. You've either set it to that
speed or you have it set for BySPD.
Click to expand...

The mobo says it autodetects the ram size and type. When I set it to
manual and 200MHz in the bios it still only reports (ghosted) 166 in the
bios. My bios is up to date.


Is it possible that Sandra is reporting incorrect values? Does the total
ram bandwidth throughput look like it's running at 200 to you?

RAM Bandwidth Int Buff'd iSSE2 : 2543 MB/s
RAM Bandwidth Float Buff'd iSSE2 : 2549 MB/s


Sandra is also telling me that my mobo only supports 768M ram.


What is BySPD?
 
Probably because it's running at 167Mhz. You've either set it to that
speed or you have it set for BySPD.
Click to expand...

Ok, I know what BySPD is now but I'm not sure what to set my timings to
in bios. Here's what I have

K8VT800 motherboard socket 754

Patriot 2x1GB Extreme Performance PC3200
PEP1G3200LL
CL 2
2-3-2-5


And here are the timings available in my bios

CAS# Latency 2.0
Row Cycle Time (tRC) 10 [7-22]
Row Refresh Cycle Time (tRFC) 11 [9-24]
RAS# to CAS# Delay (tRCD) 3 [2-7]
Row to Row Delay (tRRD) 2 [2-4]
Min RAS# Active Time (tRAS) 6 [5-15]
Row Precharge Time (tRP) 2 [2-6]
Write Recovery Time (tWR) 3 [2-3]
Write to Read Delay (tWTR) 1 [1-2]
Read to Write Delay (tRWT) 3 [1-6]
Refresh Period (tREF) 2x2592 [many choices for this]


Could you please tell me which of those that 2-3-2-5 correlates to?
Would those be the only changes I'd need to make?


I'm guessing that all I should change is tRAS from 6 to 5. Is that
correct?

I also have a bios option to autoset the dimm clock and I suppose I
should disable that...?

Thanks for any help you can offer
 
One of my ram sticks is recognized as a 166 DDR. It's an older PC3700 which
is really a hand tested, overclocked PC 2700. You will have to set your FSB
to 200 manually if you can. My motherboard doesn't allow it.It only has
100,133,166 and Auto.Auto always sees it as 166.
 
One of my ram sticks is recognized as a 166 DDR. It's an older PC3700 which
is really a hand tested, overclocked PC 2700. You will have to set your FSB
to 200 manually if you can. My motherboard doesn't allow it.It only has
100,133,166 and Auto.Auto always sees it as 166.
Click to expand...
Many, if not all PC3200 and faster ram have SPD set to 166MHz for
compatability reasons. Left with a BySPD setting will always
set them to 166Mhz. If you want anything higher, you have to manually set
it higher, or the bios has to set it higher automatically which really is
not a good idea.
 
One of my ram sticks is recognized as a 166 DDR. It's an older PC3700
which is really a hand tested, overclocked PC 2700. You will have to
set your FSB to 200 manually if you can. My motherboard doesn't allow
it.It only has 100,133,166 and Auto.Auto always sees it as 166.
Click to expand...

Same here. It has the option for 200 but doesn't really set it, so I bought
an ASUS motherboard and am pleased with it.
 
Back
Top