CPU pins bent :/

  • Thread starter Thread starter GlimmerMan
  • Start date Start date
G

GlimmerMan

my dad dropped my unused AMD 64 3500+ onto my other computer and bent
the pins. he did a custom job of re-aligning them with a screw driver
and putting into my mobo. I finished building my pc (about 5 hours
later) and started it..... it runs.... but with nothing. its just
sits there a black screen. Do ya reckon its his fault cause he will
have to buy me a new one if it is.
 
On 7 Mar 2005 05:16:04 -0500,
my dad dropped my unused AMD 64 3500+ onto my other computer and bent
the pins. he did a custom job of re-aligning them with a screw driver
and putting into my mobo. I finished building my pc (about 5 hours
later) and started it..... it runs.... but with nothing. its just
sits there a black screen. Do ya reckon its his fault cause he will
have to buy me a new one if it is.
Click to expand...

That was a 2nd mistake - using a screwdriver.:-) Straightening pins, if
feasible at all, is best done with a thin tweezer so you don't put side
stress on the base of the pins... though I'd hate to have to tackle a
939-pin job. Did you inspect the pins carefully before inserting it and
found none bent over? I'm not sure what the chances are that a pin which
appears to be still correct, might have lost good contact at its base.

What do you mean it runs? Fans and drives turning doesn't really mean
anything. Any beeps or flashing of keyboard LEDs? Assuming you have a
floppy drive, if you put a floppy in does it get as far as accessing it?
No diags on the mbrd?... some newer mbrds have diagnostics LEDs on the
board or a plug-in bracket.
 
On 7 Mar 2005 05:16:04 -0500,
my dad dropped my unused AMD 64 3500+ onto my other computer and bent
the pins. he did a custom job of re-aligning them with a screw driver
and putting into my mobo. I finished building my pc (about 5 hours
later) and started it..... it runs.... but with nothing. its just
sits there a black screen. Do ya reckon its his fault cause he will
have to buy me a new one if it is.
Click to expand...

You sure he straightened *all* the pins? You need to look very closely
through a powerful magnifying glass to see for sure. I put in a cpu
with a bent pin once and it shorted my mb and I got the same results
you have now. I found the bent pin and straightened it with tweezers
but had to send my mb back to Asus to get fixed. It was all Intel's
fault and their dastardly packaging that caused the cpu to fly up into
the air and land on the counter and get a bent pin - seriously.
 
It does not beep , no sound, the light on the mobo works though and
that is all. nothink on display. Keyboard doesnt flash.

EDIT: Got "System failed due to CPU overclocking" This is false
because i dont even get the chance to overclock as i cant get to the
BIOS menu. There is simply nothing there.

oh yeh these are the specs : AMD 64 3500+, AV8 Deluxe (WiFi) Rev 2.00,
Chaintech Gf FX 5200 256mb, Audigy 2 ZS, 1x512mb RAM @ 333mhz, 400W
thermaltake PSU. and liek 9x80mm case fans and i dont have a floppy
(wasnt much point off having one before).
 
GlimmerMan said:
my dad dropped my unused AMD 64 3500+ onto my other computer
and bent the pins. he did a custom job of re-aligning them
with a screw driver and putting into my mobo. I finished
building my pc (about 5 hours later) and started it..... it
runs.... but with nothing. its just sits there a black
screen. Do ya reckon its his fault cause he will have to
buy me a new one if it is.
Click to expand...

Yes, it _is_ his fault. First for bending the pins, then
making things _much_ worse by using the wrong tool to
straighten them.

I use empty mechanical pencils of the right size (0.3 or
0.5 mm) to straighten pins, one by one. Close enough to fit
isn't close enough. They have to ).be straight to careful
visual inspection (sight along rows).

-- Robert
 
On 7 Mar 2005 05:16:04 -0500,
my dad dropped my unused AMD 64 3500+ onto my other computer and bent
the pins. he did a custom job of re-aligning them with a screw driver
and putting into my mobo. I finished building my pc (about 5 hours
later) and started it..... it runs.... but with nothing. its just
sits there a black screen. Do ya reckon its his fault cause he will
have to buy me a new one if it is.
Click to expand...

Was your dad grounded (wrist strap) when he was trying to fix the bent
pins?, if not it's possible he could of zapped the CPU with static
electricity.

I can't imagine bending pins on these new chips, I bent some pins on a
old K6-233 recently and I about gave up before I finally fixed it!

Good Luck,
Ed
 
GlimmerMan said:
my dad dropped my unused AMD 64 3500+ onto my other computer and bent
the pins. he did a custom job of re-aligning them with a screw driver
and putting into my mobo. I finished building my pc (about 5 hours
later) and started it..... it runs.... but with nothing. its just
sits there a black screen. Do ya reckon its his fault cause he will
have to buy me a new one if it is.
Click to expand...
Have you since removed the CPU to see if any pins have broken?
 
Are you familiar with metal fatigue?
Even if you did straighten all of them back to normal, chances are;
they ain't in quite new condition... Which could block even one
stream of data from successful being transfered. And the whole
screwdriver bit: Sure it wasn't magnetic? A big hint on CPU problems
is the BIOS beeping... make sure you internal computer speaker is
connected properly and see if you get any beeps. Those are great for
troubleshooting... if the CPU doesn't work... chances are, niether
will the speaker... if do hear a beep... see if the mobo manual has a
troubleshooting guide to interpret the beeps.
 
the message from the green jack at the back was "system failed due to
cpu overclocked" or something. I figure the cpu is not fried so my
first worry is gone. Now i got some advice to update the bios by
putting in a stick of ram in the 3rd slot from the left. Hopefully it
will work.. wish me luck!
 
Back
Top