comp problems

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

My computer will not start it just keeps restarting, or if it does start it
will bring up random error messages. I have already tried to boot to last
known good configuration that did not work. I have tried to boot from CD
(after making the cd main boot) and it just passes cd and goes right to
harddrive. I cannot get into any of the safe modes, the screen will scroll
the files it needs but after that nothing, it will just sit there until I
finally turn computer off. I have waited up to 30 min.
 
Hi

You may have to alter the boot sequence in the BIOS so as to boot from the
CD.
 
When attempting to boot from the CD, you often have to watch for a message a
few screens into the boot process asking you to hit any key if you wish to
boot from the CD. Did you watch for that message and do as instructed.

If not, try again as outlined above and then try a repair install as
outlined below:
NOTE, while a repair install should leave your data files intact, if
something goes wrong during the repair install, you may be forced to start
over and do a clean install of XP. If you don't have your data backed up,
you would lose your data should that eventuality occur.

Assuming your system is set to boot from the CD-ROM drive and you have an
actual XP CD as opposed to a recovery CD, boot with the XP
CD in the drive and perform a repair install as outlined below. If the
system isn't set to boot from the CD or you are not sure, you need to enter
the system's BIOS. When you boot the system, the first screen usually has
instructions that if you wish to enter set press a specific key, when you
see that, do so. Then you will have to navigate to the boot sequence, if
the CD-ROM drive is not first line, set it first in the boot sequence. Save
your settings and exit with the XP CD in the drive. The system will reboot.

When the system boots, a few screens into the process you may see a message
instructing you
to hit any key in order to boot from the CD along with a countdown. When
you see this be sure to
hit a key on the keyboard, if you miss this instruction and the system fails
to boot from the CD, it's too
late, you'll need to reboot and try again.

Once you have pressed a key, setup should begin. You will see a reference
asking if you need to load special drivers and another notice that if you
wish to begin the ASR (Automatic Recovery Console) depress F2. Just let
setup run past all of that. It will continue to load files and drivers.

Then it will bring you to a screen. Eventually, you will come to a screen
with the option to (1) setup Windows or (2) Repair Windows Installation
using the Recovery console. ***The selection you want at this screen is
"Setup Windows,"
NOT "Repair Windows Installation.

The first option, to setup Windows is the one you want and requires you to
press enter. When asked, press F8 to accept the end user agreement. Setup
will then search for previous versions of Windows. Upon finding your
version, it will ask if you wish to Repair your current installation or
install fresh. Press R, that will run a repair installation. From there
on, follow the screens.

Note, in some cases, you won't receive the repair option, only an option to
reinstall. We have discovered that sometimes this is caused by damaged
boot.ini file that can be repaired as follows and also note, in the
instructions, "K" refers to the CD drive in which you have placed the XP CD,
replace that drive letter with the appropriate letter on your system, "K" is
simply an example.

Reboot, this time taking the immediate R option (this is the section I told
you to skip above. In this case, you will need to get to the Recovery
Console to perform the function below), and if the CD letter is say K: give
these commands

COPY K:\i386\ntldr C:
COPY K:\i386\ntdetect.com C:
(two other files needed - just in case)
ATTRIB -H -R -S C:\boot.ini
DEL C:\boot.ini
BootCfg /Rebuild

Once you've completed this function, reboot and see if you can access XP as
sometimes, the problem is the damaged boot.ini. If you still cannot access
XP, then reboot and re-run the repair install instructions at the beginning
of this message.

If you only have a recovery CD, your options are quite limited. You can
either purchase a retail version of XP which will allow you to perform the
above
among other tools and options it has or you can run your system recovery
routine with the Recovery CD which will likely wipe your drive, deleting all
files but will restore your setup to factory fresh condition.


--
Michael Solomon MS-MVP
Windows Shell/User
https://mvp.support.microsoft.com/communities/mvp.aspx
Backup is a PC User's Best Friend
DTS-L.Org: http://www.dts-l.org/
 
Sigh new problem while at work brother used win98 startup disk to reformat
hard drive. Trying to reinstall xp the system will stop to protect my
computer (blue screen with white writing at top left corner) during the
loading files needed to load the OS. process (the part right after you chose
which file system to use). Could formating with the 98 startup disk cause a
problem with xp loading? xp uses fat32 becouse that is what this comp is
using with xp.
The error message tells me to check the drivers and such but it has no OS on
it to have drivers other then the ones that windows cd loads.
 
Sorry, I hit send too quickly on that last post, here are the instructions:
Assuming your system is set to boot from the CD-ROM drive, boot with the XP
CD in the drive. If it isn't or you are not sure, you need to enter the
system's BIOS. When you boot the system, the first screen usually has
instructions that if you wish to enter setup press a specific key, when you
see that, do so. Then you will have to navigate to the boot sequence, if
the CD-ROM drive is not first line, set it first in the boot sequence. Save
your settings and exit with the XP CD in the drive. The system will reboot.

A few screens into the boot process, if you see the message on the boot
screen to "Press any key in order to boot from the CD," do so.

After loading drivers and files, you should be taken to a screen with
the following:

To Setup Windows XP now, press ENTER.
To Repair a Windows XP Installation using Recovery Console press R.
To Quit setup without installing Windows XP, press F3.

In your case, press ENTER.

Agree to the License agreement by pressing F8.

You will then be taken to a screen with two options.

To repair the selected Windows XP installation press R.
To continue installing a fresh copy of Windows XP without repairing,
press ESC.

This will bring you to a partition map where you
can delete, create and format partitions.
Select the drive you wish to format, delete the partition, then create a new
partition, format as desired and continue with XP installation.


--
Michael Solomon MS-MVP
Windows Shell/User
https://mvp.support.microsoft.com/communities/mvp.aspx
Backup is a PC User's Best Friend
DTS-L.Org: http://www.dts-l.org/
 
Thanks for all the help, got it loaded found out we had a bad mem chip. I
wonder if that had been problem all along, oh well glad I back up all the
comps around here often.
 
Back
Top