AIW 9700pro no sound while tv recording

  • Thread starter Thread starter Ron Shaw
  • Start date Start date
R

Ron Shaw

lost most control of my fingers so pleaqe bear with me, it hurts like hell 2
type.

my 9700 pro aiw works great but after installing the latest 4.6 drivers and
the multi media center
the TV setup module under personal video recorder shows the modes as

type : mpeg 2
video 704x480 ntsc

audio: No Audio <--------------what the hell?

no matter what i select or defind no audio is there and so when i record the
video is great but there is no sound.

i've re-installed everthing twice, where the heck can i change this?

any help is appreciated..

--

Ron Shaw

Please help. I am deemed a Criminal by my own government
A Marijuana User in never ending pain, I had polio now MS.
As an Engineer I designed your cars, computers & software.
Why lockup the ill? http://home.comcast.net/~rtshaw

Support Medical Marijuana visit http://www.mpp.org/MI
 
I had a similar problem before. You need to connect your sound card
to the Aux Line -In on the ATI card, then select Line-In as the audio
source. That all I did. Good luck.
 
Ron Shaw said:
lost most control of my fingers so pleaqe bear with me, it hurts like hell 2
type.

my 9700 pro aiw works great but after installing the latest 4.6 drivers and
the multi media center
the TV setup module under personal video recorder shows the modes as

type : mpeg 2
video 704x480 ntsc

audio: No Audio <--------------what the hell?

no matter what i select or defind no audio is there and so when i record the
video is great but there is no sound.

i've re-installed everthing twice, where the heck can i change this?

any help is appreciated..
Click to expand...
Make sure your set up to record from the input on the sound card that the
all-in-wonder is attached to.
 
not bad, dd that looong ago
only change was 4.6 driver. dropped back to 4.5 same thing so i hacked the
registry

--

Ron Shaw

Please help. I am deemed a Criminal by my own government
A Marijuana User in never ending pain, I had polio now MS.
As an Engineer I designed your cars, computers & software.
Why lockup the ill? http://home.comcast.net/~rtshaw

Support Medical Marijuana visit http://www.mpp.org/MI
 
not bad, dd that looong ago
only change was 4.6 driver. dropped back to 4.5 same thing so i hacked the
registry
Click to expand...

FWIW,

I've had this problem before, but it always was a "one shot deal" that just
happened, and then everything was OK.

It may very well have occurred just after driver or MMC upgrades, which I've
done several times.

Did hacking the registry solve the problem?



Henry

Posted Using Agent 2.0
[to reply, delete the AT]

******************************
 
yep

Henry said:
not bad, dd that looong ago
only change was 4.6 driver. dropped back to 4.5 same thing so i hacked the
registry
Click to expand...

FWIW,

I've had this problem before, but it always was a "one shot deal" that just
happened, and then everything was OK.

It may very well have occurred just after driver or MMC upgrades, which I've
done several times.

Did hacking the registry solve the problem?



Henry

Posted Using Agent 2.0
[to reply, delete the AT]

******************************
Click to expand...
 
It's easy to forget to select and adjust the appropriate sound card
input in the "recording controls" as well as in the "playback
controls", which I find easier to manage with the regular Windows
mixer. Normally the Audigy defaults to "what-you-hear", which should
work.

~aew
 
What did you do??

I have the same problem - in my case upgrading from Catalyst 4.6 and
MMC 9.0 to 4.7 and 9.1 produced the identical result - "Audio: No
Audio" in all the presets when it should be something like "Audio:
48.000 KHz, 16 Bit, Stereo". (An audio setting is not even available
when editing a preset.) Recording worked perfectly before this step.
No hardware changes at all, only software.

It's actually a deeper problem than no sound or low volume -
recordings viewed in a video editor have a video track, but no audio
track whatsoever. Of course, sound works fine during TV viewing.

I've gotten it working again by uninstalling everything and
reinstalling the original software from the distribution CD (after
many intermediate installations), but I want the latest versions back!
I don't give up easily either. I've been investigating the registry
too, and am getting close, but if you still have the specific keys
necessary to fix this, I'd be very greatful.

Thanks!



Ron Shaw said:
yep

Henry said:
not bad, dd that looong ago
only change was 4.6 driver. dropped back to 4.5 same thing so i hacked the
registry
Click to expand...

FWIW,

I've had this problem before, but it always was a "one shot deal" that just
happened, and then everything was OK.

It may very well have occurred just after driver or MMC upgrades, which I've
done several times.

Did hacking the registry solve the problem?



Henry

Posted Using Agent 2.0
[to reply, delete the AT]

******************************
Click to expand...
Click to expand...
 
What did you do??

I have the same problem - in my case upgrading from Catalyst 4.6 and
MMC 9.0 to 4.7 and 9.1 produced the identical result - "Audio: No
Audio" in all the presets when it should be something like "Audio:
48.000 KHz, 16 Bit, Stereo". (An audio setting is not even available
when editing a preset.) Recording worked perfectly before this step.
No hardware changes at all, only software.

It's actually a deeper problem than no sound or low volume -
recordings viewed in a video editor have a video track, but no audio
track whatsoever. Of course, sound works fine during TV viewing.

I've gotten it working again by uninstalling everything and
reinstalling the original software from the distribution CD (after
many intermediate installations), but I want the latest versions back!
I don't give up easily either. I've been investigating the registry
too, and am getting close, but if you still have the specific keys
necessary to fix this, I'd be very greatful.

Thanks!



Ron Shaw said:
yep

Henry said:
not bad, dd that looong ago
only change was 4.6 driver. dropped back to 4.5 same thing so i hacked the
registry
Click to expand...

FWIW,

I've had this problem before, but it always was a "one shot deal" that just
happened, and then everything was OK.

It may very well have occurred just after driver or MMC upgrades, which I've
done several times.

Did hacking the registry solve the problem?



Henry

Posted Using Agent 2.0
[to reply, delete the AT]

******************************
Click to expand...
Click to expand...
 
Back
Top