Accessing HD causes system to restart

  • Thread starter Thread starter Steve
  • Start date Start date
S

Steve

I recently returned from holiday to find that my computer was booting VERY
slowly. After a bit of online research, I narrowed the issue down to my HD
being faulty. I tried chkdsk and it was failing, system restore also crashed
etc. I bought a new HD today, reinstalled Windows and the machine is running
fast again.

However, when I try to access a certain folder on my *old HD* (from the
newly installed OS/HD), my machine resets itself. Every time I access this
folder, the same thing happens. I guess that the damaged disk area is where
this folder is located. I can access other folders without any problem. When
I try to run chkdsk, the machine also resets itself.

My questions are:

1) What is the problem with this area of the disc?
2) How likely is it that my whole HD will be unusable in the near future?
3) Is there any way to mark the damaged area as unusable, so that the system
doesn't reset? Can I mark an entire partition as unusable, as it seems to
only be affecting one?


TIA.
 
Big_Al said:
I'd first say run chkdsk, but you got that one down pat by now.

As for the whole drive, depends on why its a bad sector. If its dirt
floating around scratching the surface, well you got a time bomb.
Otherwise a spot could just have failed or corrupted. Impossible to say.
The drive manufacturer might have some utilities you can download and run
that might mark bad sectors, but I always thought that was a feature of
chkdsk. Still it would be a different program and it might handle drive
errors better than Windows.

But as far as a partition is concerned, you can go into drive manager in
XP and just delete it. If its not there its just gone space on the
drive. Yes, you could remake the partition and format it. Or just
format it now. And not quick format, but the long format as it is
supposed to check and mark out bad sectors. (or did years ago).
Click to expand...

The faulty disk is a Maxtor 200GB. I just tried using SeaTools, and
performing a "long test". It crashed the test program (no reset, just
frozen). At the point of crash it had reported:

0% LBA 50186 3 Error(s)

I suspect there is a serious localised hardware fault within the disk - and
everytime software encounters it, the disk fails.
 
Steve said:
I recently returned from holiday to find that my computer was booting VERY
slowly. After a bit of online research, I narrowed the issue down to my HD
being faulty. I tried chkdsk and it was failing, system restore also crashed
etc. I bought a new HD today, reinstalled Windows and the machine is running
fast again.

However, when I try to access a certain folder on my *old HD* (from the
newly installed OS/HD), my machine resets itself. Every time I access this
folder, the same thing happens. I guess that the damaged disk area is where
this folder is located. I can access other folders without any problem. When
I try to run chkdsk, the machine also resets itself.

My questions are:

1) What is the problem with this area of the disc?
2) How likely is it that my whole HD will be unusable in the near future?
3) Is there any way to mark the damaged area as unusable, so that the system
doesn't reset? Can I mark an entire partition as unusable, as it seems to
only be affecting one?


TIA.
Click to expand...
I'd first say run chkdsk, but you got that one down pat by now.

As for the whole drive, depends on why its a bad sector. If its dirt
floating around scratching the surface, well you got a time bomb.
Otherwise a spot could just have failed or corrupted. Impossible to
say. The drive manufacturer might have some utilities you can
download and run that might mark bad sectors, but I always thought that
was a feature of chkdsk. Still it would be a different program and it
might handle drive errors better than Windows.

But as far as a partition is concerned, you can go into drive manager in
XP and just delete it. If its not there its just gone space on the
drive. Yes, you could remake the partition and format it. Or just
format it now. And not quick format, but the long format as it is
supposed to check and mark out bad sectors. (or did years ago).

HTH, Al.
 
The faulty disk is a Maxtor 200GB. I just tried using SeaTools, and
performing a "long test". It crashed the test program (no reset, just
frozen). At the point of crash it had reported:

0% LBA 50186 3 Error(s)

I suspect there is a serious localised hardware fault within the disk -
and everytime software encounters it, the disk fails.
Click to expand...

Make sure you have the jumpers correctly set for master/slave on the
drives.

Every once in a while some HDs go bad. If the CD/Floppy versions of
SeaTools DOS or MaxBlast can't access the HD there's little you can do.

I'd backup from the folders that you can access. Then try to backup sub-
folders of the bad folder.

I'd try the chkdisk /f command from safe mode with only the faulty HD
installed.
 
Back
Top