A7v8x-mx restarting

  • Thread starter Thread starter John
  • Start date Start date
J

John

Just set up a new machine
I have setup lots of machines but never used this board
I used Samsung Ram 512meg
WD HDD 120 GIG
500 watt power
Pioneer ao7


On setting it up I experienced consistent rebooting
Screen goes pink squares or streaks and locks
Got Windows XP on after some time seemed to be stable after I reseated the
Ram
However when I restart the pc I get the pink squares and a reboot or two
this does not happen very often and I'm more curious more that anything else
apart from that it works Fine
Is anyone experience this Problem
 
Just set up a new machine
I have setup lots of machines but never used this board
I used Samsung Ram 512meg
WD HDD 120 GIG
500 watt power
Pioneer ao7


On setting it up I experienced consistent rebooting
Screen goes pink squares or streaks and locks
Got Windows XP on after some time seemed to be stable after I reseated the
Ram
However when I restart the pc I get the pink squares and a reboot or two
this does not happen very often and I'm more curious more that anything else
apart from that it works Fine
Is anyone experience this Problem
Click to expand...

Do you run memtest86 on the machines you build ? You shouldn't
install an OS until the memory is proved error free. Bad memory
can corrupt the install, and cause you to start all over again.
http://www.memtest.org

Your motherboard has integrated graphics, and will use the system
memory for the frame buffer and for textures. So, either the
motherboard or the memory is at fault, for pink squares or streaks.

Some integrated graphics chipsets seem to be sensitive to the
clock speed used with them. The manual for this board says you
may use up to PC2700 memory. Perhaps you've set the thing to
[By SPD] and used a PC3200 stick of ram, and the Northbridge is
running the memory interface at DDR400, when really with
the integrated graphics, it cannot handle it ?

Have you looked in the Hardware Monitor page of the BIOS, to see
whether the voltages look good ? PSU voltages have a tolerance
of 5%, so see if they are within that allowance. Your board probably
draws most of its current from +5V.

Just a guess,
Paul
 
All sounds Very reasonable.I have already changes sticks time to cross
fingers Cheers



Paul said:
Just set up a new machine
I have setup lots of machines but never used this board
I used Samsung Ram 512meg
WD HDD 120 GIG
500 watt power
Pioneer ao7


On setting it up I experienced consistent rebooting
Screen goes pink squares or streaks and locks
Got Windows XP on after some time seemed to be stable after I reseated the
Ram
However when I restart the pc I get the pink squares and a reboot or two
this does not happen very often and I'm more curious more that anything else
apart from that it works Fine
Is anyone experience this Problem
Click to expand...

Do you run memtest86 on the machines you build ? You shouldn't
install an OS until the memory is proved error free. Bad memory
can corrupt the install, and cause you to start all over again.
http://www.memtest.org

Your motherboard has integrated graphics, and will use the system
memory for the frame buffer and for textures. So, either the
motherboard or the memory is at fault, for pink squares or streaks.

Some integrated graphics chipsets seem to be sensitive to the
clock speed used with them. The manual for this board says you
may use up to PC2700 memory. Perhaps you've set the thing to
[By SPD] and used a PC3200 stick of ram, and the Northbridge is
running the memory interface at DDR400, when really with
the integrated graphics, it cannot handle it ?

Have you looked in the Hardware Monitor page of the BIOS, to see
whether the voltages look good ? PSU voltages have a tolerance
of 5%, so see if they are within that allowance. Your board probably
draws most of its current from +5V.

Just a guess,
Paul
Click to expand...
Click to expand...
 
Back
Top