a7m266 with xp2100+palimino

  • Thread starter Thread starter cobra
  • Start date Start date
C

cobra

i have a asus a7m266 rev 1.04
the bios is updated to 100.7
with the athlon 1200 thunderbird no problems.
No i just both a xp 2100+ palimino processor.
when i but the processor in the motherboard and turn it on nothing happens.
when i put the 1200 back everything runs fine

my question is are there settings i have to do , voltage slew rate etc
please somebody help me

thx in advance stefaan
 
Try setting S2K SLEW RATE CONTROL to 1 with 1200 installed then switch
to the 2100+

I do have to wonder tho if you actually have a model 6 palomino core
2100+ and not a model 8 Tbred core. 2100+ Palomino are not being
sold anymore, and its been some time since they have been.
i have a asus a7m266 rev 1.04
the bios is updated to 100.7
with the athlon 1200 thunderbird no problems.
No i just both a xp 2100+ palimino processor.
when i but the processor in the motherboard and turn it on nothing happens.
when i put the 1200 back everything runs fine

my question is are there settings i have to do , voltage slew rate etc
please somebody help me

thx in advance stefaan
Click to expand...












==================================================

ASUS P4T533 mobo
Intel P4 2.8 GHz 533MHz
ASUS V8460 Ultra GeForce 4 Ti 4600
1024 Samsung 32-Bit RIMM 4200 1066MHz RAMBUS
RD1-8X Bios Savior
Enermax EG465P-VE FMA 430W PSU
Creative Labs Audigy 2
Sony DRU-500AX DVD+-RW
TDK VeloCD 48X16X48X CD-RW
TOSHIBA SD-M1612 DVD
Seagate 80GB 7200RPM
Seagate 120GB 7200RPM
WD 60GB 5400RPM
WD 40GB 5400RPM
Promise ULTRA 133 TX2 Controller
Dlink DFE530TX+ PCI nic
Motorola Surfboard SB3100 cable modem
Linksys BEFSR41 router
Windows XP Home SP1
Direct X 9.0
 
Try setting S2K SLEW RATE CONTROL to 1 with 1200 installed then switch
to the 2100+
Click to expand...
This advice is absolutely correct, but I should tell you my
experience. I planned the upgrade for a few months. I had every
detail written down. But when it came time to make the switch, I was
so concerned with the difficulties of switching the HSF without
removing the motherboard that I forgot to change the slew rate to 1 in
advance. What an idiot! Guess what. The 2100+ Palomino booted right
up, anyway. I simply entered Setup and changed it from 3 to 1 after
the upgrade. No problems whatsoever.
I wonder what the difference was between my system and Stefaan's
I do have to wonder tho if you actually have a model 6 palomino core
2100+ and not a model 8 Tbred core. 2100+ Palomino are not being
sold anymore, and its been some time since they have been.













==================================================

ASUS P4T533 mobo
Intel P4 2.8 GHz 533MHz
ASUS V8460 Ultra GeForce 4 Ti 4600
1024 Samsung 32-Bit RIMM 4200 1066MHz RAMBUS
RD1-8X Bios Savior
Enermax EG465P-VE FMA 430W PSU
Creative Labs Audigy 2
Sony DRU-500AX DVD+-RW
TDK VeloCD 48X16X48X CD-RW
TOSHIBA SD-M1612 DVD
Seagate 80GB 7200RPM
Seagate 120GB 7200RPM
WD 60GB 5400RPM
WD 40GB 5400RPM
Promise ULTRA 133 TX2 Controller
Dlink DFE530TX+ PCI nic
Motorola Surfboard SB3100 cable modem
Linksys BEFSR41 router
Windows XP Home SP1
Direct X 9.0
Click to expand...

Ron
 
I want to upgrade my A7m266 from Athlon 1.4 to whatever is possible, I
cannot get any answers from contacting ASUS. Can anyone advise me of a
knowledge source where I can find out what is possible and what I have to
do, how do I find out about "Slew Rate"?.
Regards
Barry
 
you where right
checkt the nr on the processor and its a model 8
the schop sold me the wrong one

thx for the replays
you helpt me a lot
 
Back
Top